manualshive.com logo in svg

Yamaha EF5500DE, Owner'S Manual, Page: 56 / 72

Share
Download
Yamaha EF5500DE Owner'S Manual Download Page 56

– 51 –

STORAGE

Long term storage of your generator will require some 
preventive procedures to guard against deterioration.

Drain The Fuel

  1.  Turn the engine switch to “

5

” (STOP).

1

 “

5

” (STOP)

 2.  Remove the fuel tank cap and fuel tank filter. 

Extract the fuel from the fuel tank into an approved 
gasoline container using a commercially available 
hand siphon. Then, install the fuel tank filter and 
the fuel tank cap.

WARNING

Fuel is highly flammable and poisonous. Check 
“SAFETY INFORMATION” (See page 3) carefully.

NOTICE

Immediately wipe off spilled fuel with a clean, dry, 
soft cloth, since fuel may deteriorate painted sur-
faces or plastic parts.

  3.  Turn the engine switch to “

7

” (ON).

2

 “

7

” (ON)

  4.  Turn the fuel cock lever to ON.

3

 ON

  5.  Start the engine and leave it run until it stops.
    The engine stops in approximately 20 minutes 

time by running out of fuel.

TIP
 

9

  Do not connect with any electrical devices. 

(unloaded operation)

 

9

  Duration of the running engine depends on the 

amount of the fuel left in the tank.

1

2

705-037

3

7P5-F8199-14.indd   51

2021/06/23   11:22:19

Summary of Contents for EF5500DE









































































Reviews:

No comments