Yamaha DME4io-ES Owner'S Manual Download Page 6

Page: 6 / 48

DME8i-ES/DME8o-ES/DME4io-ES Owner’s Manual

Fore

Intr

oduction to

the DME Satellite

Contr

ols and

Connector

Connecting to

a Computer

udio I/O

Connection

Connecting to an

External De

vice

Other Functions

Ref

erences

Foreword .......................................... 7

Accessories (Please make sure the following items are

included in the package.)................................ 7

Options...........................................................................  7
About the Product Names...............................................  7
About the Firmware Version ...........................................  7
Preparation......................................................................  7

Connecting the AC power cord........................................... 7
Turning the power on and off ............................................. 7

Introduction to the DME Satellite .............. 8

Differences between DME8i-ES, DME8o-ES,

and DME4io-ES ............................................ 8

DME Satellite Features ...................................................  8
Audio System Network ...................................................  9
Glossary for the DME Satellite........................................  9
Signal Types..................................................................  11
System Examples...........................................................  12
About DME Designer ...................................................  13

Controls and Connectors ....................... 14

Front Panel ...................................................................  14
Rear Panel .....................................................................  16
Precautions for Using a Rack-mounted DME Satellite ..  17

Connecting to a Computer ..................... 18

USB Connection........................................................... 18

Network Settings............................................................... 19

Ethernet Connection ([NETWORK] Connector)......... 20

Audio I/O Connection ........................... 24

Digital Audio Connection (EtherSound Connectors).... 24
Analog Audio Connection ([INPUT] & [OUTPUT]

Connectors) ................................................. 25

Connecting to an External Device............. 26

Remote Connection ([REMOTE] Connector).............. 26

Controlling external head amplifiers

from the DME Satellite......................................... 26

Controlling a DME Satellite’s internal head amps

from a digital mixer ............................................... 27

Controlling the DME Satellite from an external device...... 27

EtherSound Connection (EtherSound Connectors)....... 28

Controlling DME Satellite’s internal head amps

from a digital mixer ............................................... 28

Network Connection ([NETWORK] Connectors) ....... 29
GPI Connection ([GPI] Connector).............................. 30

Other Functions.................................. 31

Initializing the DME Satellite........................................ 31

References ....................................... 32

Options ......................................................................... 32

ICP1.................................................................................. 32
CP4SW, CP4SF, and CP1SF............................................. 32

Troubleshooting ............................................................  33
Component ...................................................................  33
MIDI Data Format .......................................................  34

1. MIDI functions on the DME8i-ES, DME8o-ES,

and DME4io-ES ................................................... 34

2. MIDI Data Flow ........................................................... 34
3. MIDI Setup ................................................................... 34
4. MIDI Format ................................................................ 35

MIDI Implementation Chart ........................................ 37
Display Messages ........................................................... 38

Error Messages................................................................... 38
Warning Messages ............................................................. 38

General Specifications ...................................................  39
Electrical Characteristics ................................................  39
Input/Output Characteristics ........................................  42
[NETWORK] Connector (100Base-TX Ethernet,

RJ-45) .......................................................... 43

Dimensions ................................................................... 44
Index ............................................................................. 45

Contents

Summary of Contents for DME4io-ES

















































Search results

Summary of Contents for DME4io-ES

Reviews:

Yamaha DME4io-ES, Owner'S Manual, Page: 6 / 48

Search results

Summary of Contents for DME4io-ES

Reviews: