Yamaha CSD-R7, Systems Setup Manual

Page: 44 / 58

RIVAGE PM7 System Setup Guide
44
Check list
You can use the following list to check whether the basic connections for the RIVAGE PM7 system are working properly.
A n HY c ar d (HY256-TL) mu st be i n st a lled i n HY c ar d slot 1 o n the
r e ar p an el an d the I/O ra ck.
A n HY c ar d does n ot w o r k i n c ar d slots 2 an d 3 o n the r e ar p an el.
I n st a ll the c ar d i n c ar d slot 1 o n the r e ar p an el o r o n the I/O ra ck.
Fibe r optic c a bles fo r the T W INLANe n et w o r k an d CAT5e c a bles fo r the co n sole n et w o r k mu st be co nn ected
bet w ee n IN an d OUT j a cks r espectively to fo rm a r i n g topology.
Co nn ecti n g IN j a cks to IN j a cks o r OUT j a cks to OUT j a cks does n ot w o r k. M a ke s ur e yo u co nn ect the c a bles p r ope r ly.
Both po w e r A an d B fo r e a ch device mu st be t urn ed o n .
M a ke s ur e th a t t w o po w e r co r ds ar e co nn ected to e a ch device an d th a t both po w e r s w itches A an d B o n
e a ch device ar e t urn ed o n .
The I/O ra ck mu st be co nn ected to an d r ecog n ized by the syste m
(SYSTEM CONFIG sc r ee n ).
P r ess the I/O ra ck select b u tto n to set the ra ck co rr ectly
( p a ge 38).
Ch ann els mu st be a ssig n ed to the T W INLANe n et w o r k co rr ectly
(SYSTEM CONFIG sc r ee n ).
Modify ch ann el a ssig nm e n t so th a t the tot a l num be r of ch ann els
u sed o n the T W INLANe n et w o r k is 400 o r less a c r oss a ll co m po n e n ts.
Refe r to “Assig n i n g ch ann els to the T W INLANe n et w o r k
( p a ge 38)” to ma ke s ur e th a t yo ur I/O ra ck setti n gs ar e co rr ect.
Refe r to “Assig n i n g ch ann els to the T W INLANe n et w o r k
( p a ge 38)” to ma ke s ur e th a t yo ur DSP setti n gs ar e co rr ect.
The st a t u s of T W INLANe n et w o r k co mmun ic a tio n mu st be n o rma l.
(The i n dic a to r s of the HY256-TL.)
M a ke s ur e th a t the fibe r optic c a bles ar e p r ope r ly co nn ected.
The w o r d clock mu st be set co rr ectly ( W ORD CLOCK sc r ee n ).
Refe r to “Setti n g the w o r d clock ( p a ge 38)” fo r i n fo rma tio n
o n ho w to set the w o r d clock co rr ectly.
The sy n ch r o n iz a tio n mu st be fi n ished (DEVICE SYNC sc r ee n ).
P r ess the SYNC b u tto n to set the sy n ch r o n iz a tio n co rr ectly
( p a ge 37).
The o u tp u t p a tches mu st be set co rr ectly (o n the DSP e n gi n e setti n g
sc r ee n ).
Refe r to “P a tchi n g o u tp u t po r ts ( p a ge 41)” fo r i n fo rma tio n
o n ho w to p a tch o u tp u t po r ts co rr ectly.
The i n p u t po r ts mu st be p a tched co rr ectly (I n p u t P a tch sc r ee n ).
Refe r to “P a tchi n g i n p u t po r ts ( p a ge 40)” fo r i n fo rma tio n o n
ho w to p a tch i n p u t po r ts co rr ectly.
OK