Yamaha Clavinova CLP-955 Service Manual Download Page 24

Page: 24 / 25

CLP-955

■

INSPECTIONS

ORDER

NOTE

C#3

D#3

F#3

G#3

A#3

C#4

LED

SWITCH

DEMO

TRANSPOSE

FUNCTION

METRONOME

▼

TEMPO,

FUNCTION

▲

TEMPO,

FUNCTION

–/NO

+/YES

PRESET SONG

TRACK 1

TRACK 2

START/STOP

REC

GRAND PIANO 1

GRAND PIANO 2

ORDER

NOTE

D#4

F#4

G#4

A#4

C#5

D#5

SWITCH

E. PIANO 1

E. PIANO 2

HARPSICHORD

VIBRAPHONE

CHURCH ORGAN

JAZZ ORGAN

STRINGS

CHOIR

WOOD BASS

E.BASS

SPLIT

REBARB

EFFECT

TOUCH

TABLE 1

1. Checking PHONES and AUX OUT

1- 1 With 1 kHz, - 20 dBm sine wave in AUX IN L / L +R, check that AUX OUT output is as follows with no

signals on AUX R.

AUX OUT L / L +R - 10 dBm +/- 2 dB
AUX OUT R - 60 dBm or less
PHONES L - 14 dBm +/- 2 dB
PHONES R - 40 dBm or less

1- 2 With 1 kHz, - 20 dBm sine wave in AUX IN R, check that AUX OUT output is as follows with no signals on

AUX L / L +R.

AUX OUT L / L +R - 60 dBm or less
AUX OUT R - 10 dBm +/- 2 dB
PHONES L - 40 dBm or less
PHONES R - 14 dBm +/- 2 dB

2. Noise Level

If no sounds are produced, check that output is –90 dBm or less at PHONES terminals L and R.

(Minimize MIC VOLUME.)
NOTE: 0 dBm is equal to 0.775 V

Summary of Contents for Clavinova CLP-955


























Search results

Summary of Contents for Clavinova CLP-955

Reviews:

Brands by name

Popular brands

Yamaha Clavinova CLP-955, Service Manual

Search results

Summary of Contents for Clavinova CLP-955

Reviews:

Brands by name

Popular brands