Yamaha BD-S677 Service Manual Download

Page: 19 / 50

BD-S677

■

REWRITING OPU PARAMETER

OPU stands for Optical Pick-up Unit.

When the following parts are replaced, the OPU parameter must be rewritten in order that this unit operates properly.

BD mechanism unit

MAIN P.C.B.

●

Required Tools

Items supplied from Yamaha Corporation

• OPU parameter writing program: Rpower.exe

• USB-UART conversion adaptor (Part No. WW867800)

USB-UART conversion adaptor x 1, USB cable (type A to type A) x 1

Note: 4P flexible flat cable is not for the Writing OPU parameter.

• Test disc set (Part No. WW867900)

For the Playback Test: BD-ROM SL (Single Layer), BD-R DL (Dual Layer), DVD-ROM DL (Dual Layer) and CD-ROM

Note: BD-ROM DL (Dual Layer) is not for the Playback Test.

Items not supplied from Yamaha Corporation

• PC

• 2D barcode reader (which supports Data Matrix symbology)

• TV

monitor

●

Preparation and precaution

• Download the Rpower8560 2.9.69 (2012/06/14) SONY KEM480 Ver.A folder from the specified download source to

the PC.

• While writing OPU parameter, keep the other application software on the PC closed. It is also recommended to

keep the software on the task tray closed as well.

●

Outline of operation procedure

<When replacing BD mechanism unit>

1. Read the OPU parameter of a replacement BD mechanism unit in advance, and save it to the PC. (See “Reading

and saving OPU parameter”)

2. Install the replacement BD mechanism unit after removing the originally installed one.

3. Write the OPU parameter saved on the PC to the FLASH ROM on MAIN P.C.B., and check disc playback capability

consecutively. (See “Writing OPU Parameter and Playback Test”)

<When replacing MAIN P.C.B.>

1. Replace the MAIN P.C.B.

2. Remove the originally installed BD mechanism unit once.

3. Read the OPU parameter of the removed BD mechanism unit, and save it to the PC. (See “Reading and saving

OPU parameter”)

4. Reinstall the removed BD mechanism unit.

5. Write the OPU parameter saved on the PC to the FLASH ROM on MAIN P.C.B., and check disc playback capability

consecutively. (See “Writing OPU Parameter and Playback Test”)

BD-S677

Summary of Contents for BD-S677



















































Search results

Summary of Contents for BD-S677

Reviews:

Related manuals for BD-S677

Brands by name

Popular brands

Yamaha BD-S677, Service Manual

Search results

Summary of Contents for BD-S677

Reviews:

Related manuals for BD-S677

Brands by name

Popular brands