Yamaha 9.9F Owner'S Manual Download Page 18 | Manualshive

Page: 18 / 62

background image

Components

13

mercial users should conform to relevant
licensing or approval authority regula-
tions.

EMU25830

Fuel joint

This joint is used to connect the fuel line.

EMU25841

Fuel gauge

This gauge is located on either the fuel tank
cap or on the fuel joint base. It shows the ap-
proximate amount of fuel remaining in the
tank.

EMU25850

Fuel tank cap

This cap seals the fuel tank. When removed,
the tank can be filled with fuel. To remove the
cap, turn it counterclockwise.

EMU25860

Air vent screw

This screw is on the fuel tank cap. To loosen
the screw, turn it counterclockwise.

EMU25912

Tiller handle

To change direction, move the tiller handle to
the left or right as necessary.

EMU25923

Gear shift lever

Move the gear shift lever forward to engage
the forward gear or rearward to engage the
reverse gear.

EMU25941

Throttle grip

The throttle grip is on the tiller handle. Turn
the grip counterclockwise to increase speed
and clockwise to decrease speed.

1. Fuel joint

2. Fuel gauge
3. Fuel tank cap

4. Air vent screw

ZMU02284

3

1

4

2

1. Forward “ ”

2. Neutral “ ”

3. Reverse “ ”

U63V2DE0.book Page 13 Monday, February 22, 2010 9:00 AM

«
...
16
17
18
19
20
...
»

Summary of Contents for 9.9F































































Reviews:

No comments

Related manuals for 9.9F

Brand: QDI Pages: 23

otometrics HI-PRO 2

Brand: natus Pages: 22

Brand: Quick Pages: 32

Brand: JETWAY Pages: 38

Brand: ASROCK Pages: 226

Brand: ASROCK Pages: 56

Brand: Newport Pages: 30

Brand: DFI Pages: 96

Brand: Honda Pages: 132

Brand: Texas Instruments Pages: 7

25 Jet FourStroke

Brand: Mercury Pages: 110

Brand: Alinx Pages: 29

SpacePC 1232 Series

Brand: Parvus Pages: 87

Brand: Supermicro Pages: 125

Brand: Texas Instruments Pages: 21

Brand: Gigabyte Pages: 96

Brand: JETWAY Pages: 47

S2257 THUNDER 2400

Brand: TYAN Pages: 105

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands