manualshive.com logo in svg

Yamaha 2011 XVS1300AA, Owner'S Manual

Share
Download
Yamaha 2011 XVS1300AA Owner'S Manual Download Page 28

INSTRUMENT AND CONTROL FUNCTIONS

4-11

4

EAU42535

“RESET” switch 

This switch is used to reset the tripme-
ters, to set the clock and to set the
brightness control mode of the multi-
function meter unit.
See “Multi-function meter unit” on page
4-6 for detailed information.

EAU12820

Clutch lever 

The clutch lever is located at the left
handlebar grip. To disengage the
clutch, pull the lever toward the handle-
bar grip. To engage the clutch, release
the lever. The lever should be pulled
rapidly and released slowly for smooth
clutch operation.
The clutch lever is equipped with a
clutch switch, which is part of the igni-
tion circuit cut-off system. (See page
4-18.)

EAU12881

Shift pedal 

The shift pedal is located on the left
side of the motorcycle and is used in
combination with the clutch lever when
shifting the gears of the 5-speed con-
stant-mesh transmission equipped on
this motorcycle.

TIP

Use your toes or heel to shift up and
your toes to shift down.

1. Clutch lever

1. Shift pedal

2. Neutral position

1

5
4
3
2

N

1

5
4
3
2

N

1

2

U12C24E0.book  Page 11  Wednesday, November 17, 2010  9:01 AM

Summary of Contents for 2011 XVS1300AA





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands