Yamaha 2010 XVS1300AZ Owner'S Manual Download Page 73

Page: 73 / 92

PERIODIC MAINTENANCE AND ADJUSTMENT

7-31

EAU24133

Replacing the tail/brake light
bulb

1. Remove the tail/brake light lens by

removing the screws.

2. Remove the burnt-out bulb by

pushing it in and turning it counter-
clockwise.

3. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

4. Install the lens by installing the

screws.

NOTICE:

Do not over-

tighten the screws, otherwise
the lens may break.

[ECA10681]

EAU24212

Replacing a turn signal light
bulb

1. Remove the turn signal lens by re-

moving the screws.

2. Remove the burnt-out bulb by

pushing it in and turning it counter-
clockwise.

3. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

4. Install the lens by installing the

screws.

NOTICE:

Do not over-

tighten the screws, otherwise
the lens may break.

[ECA10681]

EAU42484

Replacing the license plate
light bulb

1. Remove the license plate light cov-

er by removing the bolts.

2. Pull the license plate light unit up

as shown.

1. Screw

1. License plate light cover

2. Bolt

1. License plate light unit

U12C23E0.book Page 31 Tuesday, October 20, 2009 4:17 PM

Summary of Contents for 2010 XVS1300AZ





























































































Search results

Summary of Contents for 2010 XVS1300AZ

Reviews:

Related manuals for 2010 XVS1300AZ

Brands by name

Popular brands

Yamaha 2010 XVS1300AZ, Owner'S Manual

Search results

Summary of Contents for 2010 XVS1300AZ

Reviews:

Related manuals for 2010 XVS1300AZ

Brands by name

Popular brands