manualshive.com logo in svg

Yamaha 2009 YZF-R1 (Y), Service Manual, Page: 230 / 546

Share
Download
Yamaha 2009 YZF-R1 (Y) Service Manual Download Page 230

REAR SHOCK ABSORBER ASSEMBLY

4-75

EAS14B1010

HANDLING THE REAR SHOCK ABSORBER

WARNING

EWA14B1013

This rear shock absorber contains highly 
compressed nitrogen gas. Before handling 
the rear shock absorber, read and make 
sure you understand the following informa-
tion. The manufacturer cannot be held 
responsible for property damage or per-
sonal injury that may result from improper 
handling of the rear shock absorber.
• Do not tamper or attempt to open the rear 

shock absorber.

• Do not subject the rear shock absorber to 

an open flame or any other source of high 
heat. High heat can cause an explosion 
due to excessive gas pressure.

• Do not deform or damage the rear shock 

absorber in any way. Rear shock absorber 
damage will result in poor damping per-
formance.

EAS23190

DISPOSING OF A REAR SHOCK 
ABSORBER

1. Gas pressure must be released before dis-

posing of a rear shock absorber. To release 
the gas pressure, drill a 2.0–3.0 mm (0.08–
0.12 in) hole through the rear shock 
absorber at a point 40 mm (1.57 in) from its 
end as shown.

WARNING

EWA13760

Wear eye protection to prevent eye damage 
from released gas or metal chips.

EAS23230

REMOVING THE REAR SHOCK ABSORBER 
ASSEMBLY

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there 
is no danger of it falling over.

TIP

Place the vehicle on a suitable stand so that 
the rear wheel is elevated.

2. Remove:

• Rear shock absorber assembly lower bolt 

“1”

• Connecting arm and swingarm bolt “2”

TIP

While removing the rear shock absorber 
assembly lower bolt, hold the swingarm so that 
it does not drop down.

3. Remove:

• Rear shock absorber assembly bracket 

nut “1”

• Rear shock absorber assembly

TIP

Remove the rear shock absorber assembly 
from between the swingarm and frame.

EAS23240

CHECKING THE REAR SHOCK ABSORBER 
ASSEMBLY

1. Check:

• Rear shock absorber rod

Bends/damage 

→

 Replace the rear 

shock absorber assembly.

• Rear shock absorber

Gas leaks/oil leaks 

→

 Replace the rear 

shock absorber assembly.

a. 40 mm (1.57 in)

Summary of Contents for 2009 YZF-R1 (Y)



































































































































































































































































































































































































































































































































































Reviews:

No comments