manualshive.com logo in svg

Yamaha 2009 YZF-R1 (Y), Service Manual, Page: 146 / 546

Share
Download
Yamaha 2009 YZF-R1 (Y) Service Manual Download Page 146

PERIODIC MAINTENANCE

3-31

6. Install:

• Main gallery bolt

EAS21110

CHECKING THE COOLANT LEVEL

1. Stand the vehicle on a level surface.

TIP

• Place the vehicle on a suitable stand.
• Make sure the vehicle is upright.

2. Check:

• Coolant level

The coolant level should be between the 
maximum level mark “a” and minimum 
level mark “b”.
Below the minimum level mark 

→

 Add the 

recommended coolant to the proper level.

ECA13470

• Adding water instead of coolant lowers 

the antifreeze content of the coolant. If 
water is used instead of coolant check, 
and if necessary, correct the antifreeze 
concentration of the coolant.

• Use only distilled water. However, if dis-

tilled water is not available, soft water 
may be used.

3. Start the engine, warm it up for several 

minutes, and then turn it off.

4. Check:

• Coolant level

TIP

Before checking the coolant level, wait a few 
minutes until it settles.

EAS21120

CHECKING THE COOLING SYSTEM

1. Remove:

• Side cowlings
• Lower cowlings

Refer to “GENERAL CHASSIS” on page 
4-1.

2. Check:

• Radiator “1”
• Radiator inlet hose “2”
• Radiator outlet hose “3”
• Oil cooler inlet hose “4”
• Oil cooler outlet hose “5”
• Oil cooler “6”
• Water jacket joint “7”
• Water jacket joint hose “8”
• Water pump inlet pipe “9”
• Water pump outlet pipe “10”

Cracks/damage 

→

 Replace.

Refer to “RADIATOR” on page 6-1 and 
“OIL COOLER” on page 6-5.

3. Install:

• Lower cowlings
• Side cowlings

Refer to “GENERAL CHASSIS” on page 
4-1.

Engine oil pressure

Possible causes

Below specification

• Faulty oil pump
• Clogged oil filter
• Leaking oil passage
• Broken or damaged 

oil seal

Above specification

• Leaking oil passage
• Faulty oil filter
• Oil viscosity too 

high

Main gallery bolt

8 Nm (0.8 m·kgf, 5.8 ft·lbf)

Summary of Contents for 2009 YZF-R1 (Y)



































































































































































































































































































































































































































































































































































Reviews:

No comments