manualshive.com logo in svg

Yamaha 2009 YZF-R1 (Y), Service Manual, Page: 137 / 546

Share
Download
Yamaha 2009 YZF-R1 (Y) Service Manual Download Page 137

PERIODIC MAINTENANCE

3-22

TIP

To maintain the proper wheel alignment, adjust 
both sides evenly.

c. Tighten the wheel axle nut to specification.

d. Tighten the locknuts to specification.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS21440

LUBRICATING THE DRIVE CHAIN

The drive chain consists of many interacting 
parts. If the drive chain is not maintained prop-
erly, it will wear out quickly. Therefore, the drive 
chain should be serviced, especially when the 
vehicle is used in dusty areas.
This vehicle has a drive chain with small rub-
ber O-rings between each side plate. Steam 
cleaning, high-pressure washing, certain sol-
vents, and the use of a coarse brush can dam-
age these O-rings. Therefore, use only 
kerosene to clean the drive chain. Wipe the 
drive chain dry and thoroughly lubricate it with 
engine oil or chain lubricant that is suitable for 
O-ring chains. Do not use any other lubricants 
on the drive chain since they may contain sol-
vents that could damage the O-rings.

EAS21500

CHECKING AND ADJUSTING THE STEER-
ING HEAD

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there 
is no danger of it falling over.

TIP

Place the vehicle on a suitable stand so that 
the front wheel is elevated.

2. Check:

• Steering head

Grasp the bottom of the front fork legs 
and gently rock the front fork.
Binding/looseness 

→

 Adjust the steering 

head.

3. Remove:

• Upper bracket

Refer to “HANDLEBARS” on page 4-55 
and “STEERING HEAD” on page 4-70.

4. Adjust:

• Steering head

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Remove the lock washer “1”, the upper ring 

nut “2”, and the rubber washer “3”.

b. Loosen the lower ring nut “4” and then 

tighten it to specification with a steering nut 
wrench “5”.

TIP

Set the torque wrench at a right angle to the 
steering nut wrench.

Wheel axle nut

150 Nm (15 m·kgf, 110 ft·lbf)

Locknut

16 Nm (1.6 m·kgf, 11 ft·lbf)

Recommended lubricant

Chain lubricant suitable for O-
ring chains

Summary of Contents for 2009 YZF-R1 (Y)



































































































































































































































































































































































































































































































































































Reviews:

No comments