Yamaha 2009 YZF-R1 (Y) Service Manual Download Page 134

Page: 134 / 546

PERIODIC MAINTENANCE

3-19

EAS21290

CHECKING THE REAR BRAKE HOSE

1. Check:

• Brake hose “1”

Cracks/damage/wear

→

Replace.

2. Check:

• Brake hose clamp “2”

Loose Connection

→

Tighten the clamp

bolt.

3. Hold the vehicle upright and apply rear

brake several times.

4. Check:

• Brake hose

Brake fluid leakage

→

Replace the dam-

aged hose.
Refer to “REAR BRAKE” on page 4-43.

EAS21670

CHECKING THE WHEELS

The following procedure applies to both of the
wheels.
1. Check:

• Wheel

Damage/out-of-round

→

Replace.

WARNING

EWA13260

Never attempt to make any repairs to the
wheel.

TIP

After a tire or wheel has been changed or
replaced, always balance the wheel.

EAS21650

CHECKING THE TIRES

The following procedure applies to both of the
tires.
1. Check:

• Tire pressure

Out of specification

→

Regulate.

WARNING

EWA13180

• The tire pressure should only be checked

and regulated when the tire temperature
equals the ambient air temperature.

• The tire pressure and the suspension

must be adjusted according to the total
weight (including cargo, rider, passenger
and accessories) and the anticipated
riding speed.

• Operation of an overloaded vehicle could

cause tire damage, an accident or an
injury.

NEVER OVERLOAD THE VEHICLE.

Summary of Contents for 2009 YZF-R1 (Y)



































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2009 YZF-R1 (Y)

Reviews:

Yamaha 2009 YZF-R1 (Y), Service Manual, Page: 134 / 546

Search results

Summary of Contents for 2009 YZF-R1 (Y)

Reviews: