manualshive.com logo in svg

Yamaha 2009 YZF-R1 (Y), Service Manual, Page: 131 / 546

Share
Download
Yamaha 2009 YZF-R1 (Y) Service Manual Download Page 131

PERIODIC MAINTENANCE

3-16

EAS21160

ADJUSTING THE FRONT DISC BRAKE

1. Adjust:

• Brake lever position

(distance “a” from the throttle grip to the 
brake lever)

TIP

• While pushing the brake lever forward, turn 

the adjusting dial “1” until the brake lever is in 
the desired position.

• Adjust the groove of the adjusting dial to the 

 mark “2” at preferable position.

WARNING

EWA13060

• After adjusting the brake lever position, 

make sure the pin on the brake lever 
holder is firmly inserted in the hole in the 
adjusting dial.

• A soft or spongy feeling in the brake lever 

can indicate the presence of air in the 
brake system. Before the vehicle is oper-
ated, the air must be removed by bleeding 
the brake system. Air in the brake system 
will considerably reduce in loss of control 
and possibly an accident. Therefore, 
check and if necessary, bleed the brake 
system.

ECA13490

After adjusting the brake lever position, 
make sure there is no brake drag.

EAS21250

CHECKING THE FRONT BRAKE PADS

The following procedure applies to all of the 
brake pads.

1. Operate the brake.
2. Check:

• Front brake pad

Wear indicators “1” almost touch the 
brake disc 

→

 Replace the brake pads as 

a set.
Refer to “FRONT BRAKE” on page 4-30.

EAS21190

ADJUSTING THE REAR DISC BRAKE

1. Check:

• Brake pedal position

(distance “a” from the center of the foot-
rest bracket bolt to the center of the brake 
pedal)
Out of specification 

→

 Adjust.

2. Adjust:

• Brake pedal position

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Loosen the locknut “1”.
b. Turn the adjusting bolt “2” in direction “a” or 

“b” until the specified brake pedal position 
is obtained.

Direction “b”

Brake lever distance “a” is increased.

Direction “c”

Brake lever distance “a” is decreased.

Brake pedal position

12–18 mm (0.47–0.71 in)

Direction “a”

Brake pedal is raised.

Direction “b”

Brake pedal is lowered.

Summary of Contents for 2009 YZF-R1 (Y)



































































































































































































































































































































































































































































































































































Reviews:

No comments