Yamaha 2009 XV250Y Owner'S Manual Download | Manualshive

Page: 52 / 84

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-17

7

EAU22093

Adjusting the brake lever free
play

The brake lever free play should mea-
sure 2.0–5.0 mm (0.08–0.20 in) as
shown. Periodically check the brake le-
ver free play and, if necessary, adjust it
as follows.

1. Loosen the locknut at the brake le-

ver.

2. To increase the brake lever free

play, turn the brake lever free play
adjusting screw in direction (a). To
decrease the brake lever free play,
turn the adjusting screw in direc-
tion (b).

3. Tighten the locknut.

WARNING

EWA10630

●

After adjusting the brake lever
free play, check the free play
and make sure that the brake is
working properly.

●

A soft or spongy feeling in the
brake lever can indicate the
presence of air in the hydraulic
system. If there is air in the hy-
draulic system, have a Yamaha
dealer bleed the system before
operating the motorcycle. Air in
the hydraulic system will dimin-
ish the braking performance,
which may result in loss of con-
trol and an accident.

EAU22201

Adjusting the brake pedal po-
sition and free play

WARNING

EWA10670

It is advisable to have a Yamaha
dealer make these adjustments.

Brake pedal position

The top of the brake pedal should be
positioned approximately 60.0 mm
(2.36 in) above the top of the footrest as
shown. Periodically check the brake
pedal position and, if necessary, adjust
it as follows.

1. Locknut

2. Brake lever free play adjusting screw
3. Brake lever free play

1. Footrest

2. Distance between brake pedal and footrest
3. Brake pedal free play

U2UJ26E0.book Page 17 Thursday, May 22, 2008 10:21 AM

«
...
50
51
52
53
54
...
»

Summary of Contents for 2009 XV250Y





















































































Reviews:

No comments

Related manuals for 2009 XV250Y

Brand: Caberg Pages: 16

Brand: Dakota Digital Pages: 6

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: ACERBIS Pages: 72

Brand: Suzuki Pages: 199

Brand: KTM Pages: 90

Brand: Malaguti Pages: 242

Brand: PUIG Pages: 2

Brand: DYNATEK Pages: 4

Brand: Yamasaki Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands