background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-1

7

EAU17241

Periodic inspection, adjustment, and lu-
brication will keep your vehicle in the
safest and most efficient condition pos-
sible. Safety is an obligation of the vehi-
cle owner/operator. The most important
points of vehicle inspection, adjust-
ment, and lubrication are explained on
the following pages.
The intervals given in the periodic
maintenance and lubrication chart
should be simply considered as a gen-
eral guide under normal riding condi-
tions. However, depending on the
weather, terrain, geographical location,
and individual use, the maintenance in-
tervals may need to be shortened.

WARNING

EWA10321

Failure to properly maintain the ve-
hicle or performing maintenance ac-
tivities incorrectly may increase
your risk of injury or death during
service or while using the vehicle. If
you are not familiar with vehicle ser-
vice, have a Yamaha dealer perform
service.

WARNING

EWA15121

Turn off the engine when performing
maintenance unless otherwise
specified.

A running engine has moving
parts that can catch on body
parts or clothing and electrical
parts that can cause shocks or
fires.

Running the engine while ser-
vicing can lead to eye injury,
burns, fire, or carbon monoxide
poisoning – possibly leading to
death. See page 2-1 for
 more in-
formation about carbon monox-
ide.

EAU17341

Owner’s tool kit 

The owner’s tool kit is located behind
panel A. (See page 7-6.)
The service information included in this
manual and the tools provided in the
owner’s tool kit are intended to assist
you in the performance of preventive
maintenance and minor repairs. How-
ever, additional tools such as a torque
wrench may be necessary to perform
certain maintenance work correctly.

TIP

If you do not have the tools or experi-
ence required for a particular job, have
a Yamaha dealer perform it for you.

1. Owner’s tool kit

U2UJ26E0.book  Page 1  Thursday, May 22, 2008  10:21 AM

Summary of Contents for 2009 XV250Y





















































































Reviews: