manualshive.com logo in svg

Yamaha 2009 Waverunner FZR, Owner'S Manual

Share
Download
Yamaha 2009 Waverunner FZR Owner'S Manual Download Page 8

General and important labels

3

EJU30430

Manufactured date label 

This label is attached to the top of the cylinder
head.

EJU30440

Star labels 

This watercraft is labeled with a California Air
Resources Board (CARB) star label. See be-
low for a description of your particular label.

One Star - Low Emission

The one-star label identifies engines that
meet the Air Resources Board’s Personal
Watercraft and Outboard marine engine 2001
exhaust emission standards. Engines meet-
ing these standards have 75% lower emis-
sions than conventional carbureted two-
stroke engines. These engines are equivalent
to the U.S. EPA’s 2006 standards for marine
engines.

Two Stars - Very Low Emission

The two-star label identifies engines that meet
the Air Resources Board’s Personal Water-
craft and Outboard marine engine 2004 ex-
haust emission standards. Engines meeting
these standards have 20% lower emissions
than One Star-Low Emission engines.

Three Stars - Ultra Low Emission

The three-star label identifies engines that
meet the Air Resources Board’s Personal
Watercraft and Outboard marine engine 2008

1

Manufactured date label location

1

Star label location

1

1

UF2R10E0.book  Page 3  Friday, October 31, 2008  9:14 AM

Summary of Contents for 2009 Waverunner FZR









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands