Yamaha 2008 YZF-R1X Page 88 Owner'S Manual Download

Page: 88 / 108

PERIODIC MAINTENANCE AND MINOR REPAIR

6-39

3. Remove the defective bulb by pull-

ing it out.

4. Insert a new bulb into the socket.
5. Install the socket (together with the

bulb) by pushing it in.

6. Install the license plate light unit by

installing the screws.

EAU33910

Replacing an auxiliary light
bulb

This model is equipped with two auxil-
iary lights. If an auxiliary light bulb burns
out, replace it as follows.

1. Remove panel C (if replacing the

left auxiliary light bulb) or panel D
(if replacing the right auxiliary light
bulb). (See page 6-7.)

2. Remove the auxiliary light bulb

cover by removing the quick fas-
tener.

NOTE:

Remove the quick fastener by pushing
the center pin in with a screwdriver,
then pulling the fastener out.

3. Remove the socket (together with

the bulb) by pulling it out.

4. Remove the defective bulb by pull-

ing it out.

5. Insert a new bulb into the socket.
6. Install the socket (together with the

bulb) by pushing it in.

1. Auxiliary light bulb cover

2. Quick fastener

1. Auxiliary light bulb socket

1. Auxiliary light bulb

U4C821E0.book Page 39 Tuesday, July 17, 2007 11:37 AM

Summary of Contents for 2008 YZF-R1X













































































































Search results

Summary of Contents for 2008 YZF-R1X

Reviews:

Related manuals for 2008 YZF-R1X

Brands by name

Popular brands

Yamaha 2008 YZF-R1X, Owner'S Manual

Search results

Summary of Contents for 2008 YZF-R1X

Reviews:

Related manuals for 2008 YZF-R1X

Brands by name

Popular brands