Yamaha 2008 YZF-R1X Owner'S Manual Download | Manualshive

Page: 71 / 108

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-22

6

WARNING

EWA10600

This motorcycle is fitted with super-
high-speed tires. Note the following
points in order to make the most ef-
ficient use of these tires.

●

Use only the specified replace-
ment tires. Other tires may run
the danger of bursting at super
high speeds.

●

Brand-new tires can have a rela-
tively poor grip on certain road
surfaces until they have been
“broken in”. Therefore, it is ad-
visable before doing any high-
speed riding to ride conserva-
tively for approximately 100 km
(60 mi) after installing a new tire.

●

The tires must be warmed up
before a high-speed run.

●

Always adjust the tire air pres-
sure according to the operating
conditions.

EAU21960

Cast wheels

To maximize the performance, durabil-
ity, and safe operation of your vehicle,
note the following points regarding the
specified wheels.

●

The wheel rims should be checked
for cracks, bends or warpage be-
fore each ride. If any damage is
found, have a Yamaha dealer re-
place the wheel. Do not attempt
even the smallest repair to the
wheel. A deformed or cracked
wheel must be replaced.

●

The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse han-
dling characteristics, and a short-
ened tire life.

●

Ride at moderate speeds after
changing a tire since the tire sur-
face must first be “broken in” for it
to develop its optimal characteris-
tics.

EAU33890

Adjusting the clutch lever free
play

The clutch lever free play should mea-
sure 10.0–15.0 mm (0.39–0.59 in) as
shown. Periodically check the clutch le-
ver free play and, if necessary, adjust it
as follows.
To increase the clutch lever free play,
turn the adjusting bolt at the clutch lever
in direction (a). To decrease the clutch
lever free play, turn the adjusting bolt in
direction (b).

1. Clutch lever free play adjusting bolt

2. Clutch lever free play

U4C821E0.book Page 22 Tuesday, July 17, 2007 11:37 AM

«
...
69
70
71
72
73
...
»

Summary of Contents for 2008 YZF-R1X













































































































Reviews:

No comments

Related manuals for 2008 YZF-R1X

Power Commander III 718-411

Brand: Dynojet Pages: 3

Brand: hepco & becker Pages: 5

WOLVERINE R MAX 2021

Brand: Yamaha Pages: 190

Brand: Yamaha Pages: 194

WOLVERINE RMAX2 2024

Brand: Yamaha Pages: 196

Vstar XVS650T 2004

Brand: Yamaha Pages: 101

Brand: MSD Ignition Pages: 16

Brand: Yamaha Pages: 15

Brand: Yamaha Pages: 84

MSS X9 EVOLUTION 250

Brand: PIAGGIO Pages: 262

MP3 500 ie SPORT Business LT 2011

Brand: PIAGGIO Pages: 375

Brand: Norton Pages: 69

BLITZ 9-13 Visor

Brand: Fubag Pages: 17

Brand: Scott Safety Pages: 67

Brand: Buell Pages: 28

BOOMERANG 7554CB

Brand: Bagster Pages: 2

Brand: TGB Pages: 219

Brand: hepco & becker Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands