Yamaha 2006 FJR1300AS Service Manual Download Page 59

Page: 59 / 150

ENGINE REMOVAL

– 50 –

ET2D21005

ADJUSTING THE GEAR POSITION SENSOR

1. Check:

• Gear position sensor

Refer to “CHECKING THE GEAR POSITION
SENSOR” on page 132.

2. Adjust:

• Gear position sensor angle

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Connect the gear position sensor coupler to

the gear position sensor.

b. Connect the digital circuit tester to the gear

position sensor.

c. Turn the main switch to “ON”.
d. Measure the gear position sensor voltage.
e. Adjust the gear position sensor angle so that

the voltage is within the specified range.

f. After adjusting the gear position sensor an-

gle, tighten the gear position sensor screws
“3” to specification.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

3. Check:

• Gear position setting

Refer to “Diagnostic code table (Diagnostic
code No. Sh_ _65)”.

• Positive tester probe

→

yellow “1”

• Negative tester probe

→

black/blue “2”

Digital circuit tester

90890-03174

Model 88 Multimeter with ta-
chometer

YU-A1927

Output voltage (at neutral posi-
tion)

0.71–0.91 V

Gear position sensor screw

4 Nm (0.4 m·kg, 2.9 ft·lb)
LOCTITE

Summary of Contents for 2006 FJR1300AS























































































































































Search results

Summary of Contents for 2006 FJR1300AS

Reviews:

Brands by name

Popular brands

Yamaha 2006 FJR1300AS, Service Manual

Search results

Summary of Contents for 2006 FJR1300AS

Reviews:

Brands by name

Popular brands