SAD-1460 6-U
nit
M
Ulti
C
hArger
The
SAD-1460
is a rugged 6-Unit Multi Charger that enables recharging of Lithium-Ion battery pack for Yaesu
transceivers. Check with your Yaesu dealer for a list of current transceivers that may be used with the
SAD-1460
6-Unit Multi Charger.
O
perAtiOn
1. Insert the DC plug from the
SAD-60
AC Adaptor into
the DC jack on the bottom side of the
SAD-1460
6-Unit Multi Charger, then affix the DC plug using
the supplied bracket and two screws.
2. Plug the
SAD-60
AC Adaptor into the AC line outlet.
3. Insert the battery pack into any charger slot of the
SAD-1460
while aligning the slots of the battery
pack with the guides in the nest of the slot; refer
to the illustration below for details on proper posi-
tioning of the pack. If charging with the transceiver
attached, turn the transceiver off, and the antenna
jack should be at the left side when viewing the
charger from the front.
4. If the battery pack is inserted correctly, the LED
indicator will glow red. A fully-discharged pack will
charge completely in 1.5 - 3.5 hours (depending
on the battery being charged).
5. When charging is completed, the LED indicator
will change to green.
6. Disconnect the pack from the charger slot.
i
MpOrtAnt
n
OteS
!
Do not connect an improper AC Adaptor. Use only
the supplied
SAD-60
AC Adaptor.
Do not charge an improper battery (one not specif-
ically designed for use in the
SAD-1460
).
Disconnect the pack from the
SAD-1460
charger
slot when charging is completed.
Unplug the
SAD-60
AC Adaptor from the wall AC
outlet when the charger is not in use.
The
SAD-60
AC Adaptor and
SAD-1460
Multi Char-
ger will generate a moderate amount of heat during
the charging process. This is a normal condition.
The
SAD-1460
6-Unit Multi Charger is designed
for charging only, and is not designed for operation
(transmission/reception) of the transceiver.
If the LED blinks red, please insert the battery
again. If LED continues blinking red, a charger slot
or a battery may be defective. Please contact your
Yaesu dealer.
Periodically wipe the charging terminals in the nest
in the charger stand, using a dry cloth, to ensure
good connections between the charger and battery.
The
SAD-60
AC Adaptor and
SAD-1460
Multi
Charger are designed for indoor use
only
.
C
AUtiOn
!!
When charging a battery pack alone (not attached
to the transceiver), do not allow any metal object
to short the terminals on top of the pack.
Do not allow any metal objects to short the ter-
minals in the nest of the charger stand, as a
short-circuit could cause overheating of the char-
ger circuitry.
LED Status
STEADY RED
Rapid Charging
FLASHING RED
Abnormally Charging
STEADY GREEN
Charging is Completed
STEADY YELLOW
Battery Checking (Waiting to Charge)
S
peCifiCAtiOnS
Charging Current
: 1000 mA ± 100 mA
Charge Time
: 1.5 - 3.5 hours (Depends on Battery Pack)
Operating Temperature Range
: +32 °F to +104 °F
(0 °C to +40 °C)
SAD-1460 Case Size
: 11.6” x 6.2” x 14.1”
(W x H x D)
(294 x 157 x 358 mm)
SAD-1460 Weight
(approx.): 9.2 lb (4.2 kg)
SAD-60 Input Voltage
: 100-240 VAC, 50/60 Hz
SAD-60 Output Voltage
: 15 VDC
SAD-60 Output Current
: 9.6 A
S
yMbOlS
plACeD
On
the
eqUipMent
Direct current
Align the slots of the battery pack
with the guides in the nest of the
SAD-1460
6-Unit Multi Charger.
