Page 102
O
PERATING
M
ANUAL
5-1 8.2-2.0
2nd IF 2.0 kHz Filter
- Enables/disables the op-
tional 2.0 kHz IF filter (Yaesu P/N
YF-114SN
).
5-2 CW nor
CW Normal Filters
- Selects the CW filters used
when the front-panel [
NOR
] switch is selected (while
in the CW mode).
8.2
- Sets the 2nd IF to the optional 2.0 kHz filter,
and the 3rd IF to the 2.4 kHz filter.
455
- Sets the 2nd IF to the 2.4 kHz filter, and the
3rd IF to the optional 2.0 kHz filter.
8.2-455
- Sets the 2nd IF and 3rd IF filters to 2.0
kHz filter options.
Note
: If you have not installed the optional 2.0 kHz
filters (or if you disable the optional 2.0 kHz filters by
menu selection 5-1
and/or
5-5
), the received signal will
pass through the standard 2.4 kHz filter.
5-3 8.2-250
2nd IF 250 Hz Filter
- Enables/disables the optional
250 Hz IF filter (Yaesu P/N
YF-114CN
).
5-4 dAtAnAr2
DATA Narrow 2 Filters
- Selects the filters used
when the front-panel [
NAR2
] switch is selected (while
in the DATA mode).
8.2
- Sets the 2nd IF to the optional 250 Hz filter,
and the 3rd IF to the optional 500 Hz filter.
455
- Sets the 2nd IF to the 500 Hz filter, and the
3rd IF to the optional 250 Hz filter.
8.2-455
- Set the 2nd IF and 3rd IF filters to the 250
Hz filter options.
Note (1)
: If you have not installed the optional 2nd
IF 500 Hz filter (or if you disable the filter by
menu se-
lection 5-3
), the received signal will pass through the
supplied 500 Hz filter.
Note (2)
: If you have not installed the optional 3rd
IF 500 Hz filter (or if you disable the filter by
menu se-
lection 5-6
), the received signal will pass through the
supplied 2.4 kHz filter.
Note (3)
: If you have not installed the optional 3rd
IF 250 Hz filter (or if you disable the filter by
menu se-
lection 5-7
), the received signal will pass through the
supplied 2.4 kHz (or optional 500 Hz) filter.
5-5 455-2.0
3rd IF 2.0 kHz Filter
- Enables/disables the op-
tional 2.0 kHz IF filter (Yaesu P/N
YF-110SN
).
Menu Selection and Settings
5-6 455-500
3rd IF 500 Hz Filter
- Enables/disables the optional
500 Hz IF filter (Collins
YF-115C
).
5-7 455-250
3rd IF 250 Hz Filter
- Enables/disables the optional
250 Hz IF filter (Yaesu P/N
YF-110CN
).
5-8 Sub-FiL
SUB VFO Filter
- Enables/disables optional SUB
VFO-B 2nd IF 500-Hz CW filter (Collins
YF-115C
).
5-9 t-FiL
TX EDSP Filter
- Selects either a 6.0-kHz or 2.4-
kHz digital bandpass filter for early-stage transmit au-
dio tailoring.
6-0 rttY-SHF
RTTY Frequency Shift
- Selects 170, 425, or 850
Hz standard frequency shift for FSK RTTY operation.
Important Note!
- If changing RTTY shift to other
than 170 Hz, be sure to re-calibrate the tuning meter
as outlined on page 85. The calibration routine is simple,
and ensures your center tuning indication matches the
tone pair.
6-1 rttY-PoL
RTTY Polarity
- Selects normal or reverse Mark/
Space polarity for RTTY operation. Normal operation
utilizes a 2125-Hz mark frequency, while reverse uses
2295 Hz. See the table on page 17 for a list of stan-
dard tone pairs.
6-2 rttY-ton
RTTY Tone
- Selects high or low mark tone for
RTTY operation. See the table on page 17 for a com-
parison of high/low tone pairs.
6-3 rtY-FdSP
RTTY Frequency Display
- Selects the type of dis-
play offset that appears during RTTY operation.
Offset
- Displays the RTTY BFO offset.
Carrier
- Displays the actual carrier frequency.
6-4 PAc-FdSP
Packet Frequency Display Offset
- You can off-
set the frequency readout to display the center fre-
quency between the two transmitted carriers (tone
pairs). Rotate the
MAIN VFO-A
knob to adjust the dis-
play offset, or else set to 0.00 to display the actual car-
rier frequency. See
menu selection 6-5
below for tone
pair selection.
Summary of Contents for MARK-V FT-100MP
Page 119: ......
