Yaesu FT-25 Page 35 Advance Manual Download

Page: 35 / 39

FT-25R/FT-25E Advance Manual

Cloning

The

FT-25R/E

includes a convenient “Clone” feature, which allows the memory and

configuration data from one transceiver to be transferred to another

FT-25R/E

. This can

be particularly useful when configuring a number of transceivers for a public service
operation. Here is the procedure for cloning data from one transceiver to another:

1. Turn both transceivers OFF.
2. Connect the optional

SCU-36

Cloning Cable between the MIC jacks of the two trans-

ceivers.

MIC Jack

SCU-36 (optional)

3. Press and hold the

MONI/T.CALL

key and the

PTT

switch simultaneously, while turn-

ing the transceiver ON.

Do this for both transceivers (the order of switch-on does not matter).

Press the [▲] or [▼] key on each transceiver to select “

F8 : CLONE

”, then press the

key momentarily.

When the Clone mode is successfully activated in this
step, “

CLONE

” message will appear on the displays of

both transceivers.

5. Press the

PTT

switch on the Source transceiver.

• “

- - TX - -

” will appear on the Source transceiver, and

the data from this transceiver will be transferred to
the destination transceiver.

• “

- - RX - -

” will appear on the destination transceiver.

• The data from the source transceiver will be transferred

to the destination transceiver.

6. If there is an error during the cloning process, “

CLONE

ERR

” will be displayed. Check the cable connections

and battery voltage, and try again.

7. If the data transfer is successful, “

CLONE OK

” will appear on both displays.

8. Turn both transceivers off and disconnect the cloning cable.

Summary of Contents for FT-25







































Search results

Summary of Contents for FT-25

Reviews:

Related manuals for FT-25

Brands by name

Popular brands

Yaesu FT-25, Advance Manual

Search results

Summary of Contents for FT-25

Reviews:

Related manuals for FT-25

Brands by name

Popular brands