Active Tuning Antenna System
ATAS-25
Installation/Operating Instructions
Thank you for choosing Yaesu’s exciting new
ATAS-25
Active Tuning Antenna System. We hope and trust that you will enjoy many
years of enjoyable field operation with the
ATAS-25
!
The ATAS-25 utilizes a manual tuning system which resonates the radiating element for lowest SWR without the need for expen-
sive, inconvenient mono-band resonating whip assemblies. The
ATAS-25
allows dual-frequency operation (on HF or 50 MHz and
either 144 or 430 MHz), if two transceivers are combined via a suitable diplexer (not supplied). The
ATAS-25
is designed to mount
directly onto a standard camera tripod (not supplied); see Figure 1.
I
NSTALLATION
1. Mount the
ATAS-25
main body onto the tripod.
2. Referring to Figure 2 and the following chart, connect the
radiating elements according to the operating band, then
screw the radiating element securely to the top of the coil
assembly of the
ATAS-25
.
O
PERATING
B
AND
R
ADIATING
E
LEMENT
(
S
)
7 MHz
Three Elements
14 MHz
Three or Two Elements
21 MHz
Two Elements
28 MHz
Two or One Element(s), or No Connection
50 MHz
Do Not Connect
144 MHz
Not Used
430 MHz
Not Used
NOTE: When the ATAS-25 is fitted with two radiating
elements, use the top radiating element (the one with
the rubber cap) and the bottom radiating element (the
one with the threaded adapter at the bottom). When the
ATAS-25 is fitted with only one radiating element, move
the threaded adapter to the bottom of the element with
the rubber cap, then screw that element onto the top of
the coil assembly (Figure 3).
3. Secure the V/UHF radial elements to the bottom of the
ATAS-
25
main body, using the supplied Allen wrench (Figure 4).
4. Connect the supplied radial wires to the bottom of the
ATAS-
25
main body, then extend them outward from the antenna
base (Figure 5).
5. Connect the coaxial cable from the transceiver’s HF an-
tenna jack (see Figure 6). Typically, you can use the built-
in SWR meter in the transceiver, but alternatively you may
adjust the SWR using an “Antenna Analyzer” prior to con-
necting the coaxial cable to your transceiver.
If you operate the
ATAS-25
along with the
FT-817
, we recom-
mend that you set the transceiver’s
Menu #07
(ANTENNA) to
“
REAR
” for all bands (HF/50/144/430 MHz), to pass all bands’ RF
power to the rear antenna jack of the
FT-817
. Refer to the
FT-817
operating manual for details regarding the Menu selections.
For operation on the 144 and 430 MHz bands, in addition to HF/
50 MHz using the
FT-847
/
-100
/
-100D
/
-857
/
-897
, you may wish
to consider the purchase of a “Diplexer” (for the
FT-100
/
-100D
/
-857
/
-897
) or “Triplexer” (for the
FT-847
) device to contact to the
appropriate transceiver’s antenna jack; the Diplexer or Triplexer
will then automatically pass RF power from the band in use while
isolating the other one or two jacks. If you do not have a Diplexer
or Triplexer, the coaxial cable connector from the
ATAS-25
will
Figure 1
Coarse Tuning
Fine Tuning
Figure 2
Figure 4
Figure 6
E A C 8 2 X 7 0 0
S
PECIFICATIONS
Frequency Range
: 7/14/21/28/50/144/430 MHz
Amateur Bands
Input Impedance
: 50 Ohms
Max. Input Power
: HF/50 MHz:
100 W
(SSB/CW, 50% Duty)
50 W
(AM/FM)
144/430 MHz: 50 W
(ALL MODE)
Matched SWR
:
Less than 2.0:1
Height
(Approx.):
Max. 7.2 ft (2.2 m) during Operation
Min. 1.96 ft (0.6 m) for Transporting
Weight
(Approx.):
2.05 lb. (930 g)
S
UPPLIED
I
TEMS
ATAS-25 Main Body .............................................................. 1
Radiating Elements .............................................................. 3
Radial Element (for VHF band) ............................................ 1
Radial Element (for UHF band) ............................................ 1
Radial Wires (20 ft (6 m) , 9.8 ft (3 m) & 6.6 ft (2 m) Length) ...
1
Spare Radial Wire (32.8 ft (10 m) Length) ........................... 1
Allen Wrench ........................................................................ 1
Operating Manual ................................................................. 1
VERTEX STANDARD CO., LTD.
4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan
VERTEX STANDARD
US Headquarters
10900 Walker Street, Cypress, CA 90630, U.S.A.
YAESU EUROPE B.V.
P.O. Box 75525, 1118 ZN Schiphol, The Netherlands
YAESU UK LTD.
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
VERTEX STANDARD HK LTD.
Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road,
Kwun Tong, Kowloon, Hong Kong
Figure 5
C
AUTIONS
The
ATAS-25
is designed for temporary field operation.
We do not recommend that the
ATAS-25
be used for per-
manent operation, as it does not include the weatherproof-
ing needed for long-term outdoor installation.
The
ATAS-25
is designed for a maximum power of 100
Watts (SSB/CW) or 50 Watts (AM/FM, 144 MHz, 430 MHz).
Do not exceed this combined power input (if two transmit-
ters are connected via a diplexer) when operating the
ATAS-
25
.
Do not connect (mount) the
ATAS-25
to the antenna jack
of the transceiver or antenna mount directly using a double-
male coaxial adapter plug. The
ATAS-25
must be mounted
onto a tripod or other similar item using the Camera Screw
hole (Type “U¼”) on the bottom of the
ATAS-25
main body.
Do not allow anyone to touch the radiating element during
a transmitting session, due to the danger of burning of the
skin caused by the high RF voltage present. It helps the
accuracy of the SWR measurements if all people are stand-
ing at least 10 feet (3 m) away from the radiating element,
anyway, to minimize inaccuracies due to mutual coupling
to the human figure(s) in the vicinity.
If erratic transceiver operation is observed, there may be
common-mode current flowing on the shield of the coaxial
cable. Make an RF choke by coiling about eight turns of
cable into a coil of diameter approximately 6” (roughly 150
mm) near the
ATAS-25
, taping the coils to hold them in
place. If this does not eliminate the problem, reverse the
coax ends, placing the coil near the transceiver. If addi-
tional cable is available, place a coil at both ends of the
coaxial cable in difficult cases.
Set up the tripod as low and level as possible, for maxi-
mum stability of the tripod/antenna assembly. SWR tends
to be best with the base of the
ATAS-25
near the ground,
as well (Figure 1).
Should the
ATAS-25
get wet due to rain, wipe off the
antenna’s components using a dry cloth, then completely
dry the
ATAS-25
overnight with the coil assembly fully ex-
tended.
For SSB/CW DX operation on the 144/430 MHz bands,
remember that the convention for polarization in most ar-
eas is horizontal, not vertical, so we recommend the
ATAS-
25
mostly for local FM work on those bands.
Make every effort to install the
ATAS-25
away from areas
where people might trip over the tripod legs, coaxial cable,
or counterpoise wires. We strongly recommend that the
tripod legs be staked firmly to the ground, or the tripod and
antenna be otherwise secured with guy ropes and stakes,
to prevent the antenna from accidentally tipping over, so
as to avoid injury to bystanders and/or damage to antenna
components.
Figure 7
O
PERATION
For the 144/430 MHz bands, you may operate instantly with-
out making any adjustments. For HF/50 MHz operation, per-
form the following procedures for antenna adjustment:
1. Tune the transceiver to the desired operating frequency.
2. Referring to Figure 7, raise and lower the coil assembly
while listening to the band noise, and seek the position of
the coil assembly producing the most noise in the receiver.
If a peak in the sensitivity is not obtained when the coil
assembly is fully retracted to the lowest (shortest) posi-
tion, remove one radiating element from the coil assembly
and try again. You may have a total antenna length that is
too long.
3. Key the transmitter in the CW mode, and check the SWR
meter reading.
4. Referring to Figure 7 again, carefully turn the coil assem-
bly to the right or to the left while the transceiver is receiv-
ing. After making an adjustment, stand away from the an-
tenna and check the SWR again, and repeat (or reverse)
the procedure until the best SWR is obtained.
Do not touch
the coil assembly during a transmitting session.
5. If low SWR on an HF band cannot be satisfactorily ob-
tained, connect (add) the supplied spare radial wire to the
bottom of the
ATAS-25
main body and extend it outward
from the antenna base, then try the above procedures
again.
Figure 3
have to be moved manually to the appropriate antenna jack when
you wish to operate on VHF or UHF.
While operation is not guaranteed on the 10/18/24 MHz bands,
please feel free to experiment on these bands, as low SWR and
good efficiency will be obtained in many instances.
