background image

NitraVis 70x IQ TS

Measurement / Operation

 23

ba75952e03

05/2017

4.2

Measurement operation

Measured value

display

Fig. 4-2 NitraVis 70x IQ TS

 

Factors affecting the

measured values

The following factors can adversely affect the measurement quality:

The measuring gap is not sufficiently filled and flowed through by the test 

sample

Foreign bodies and air bubbles are in the measuring gap

Extraordinary changes (interferences) of the sample matrix

Contaminated measurement windows due to difficult sample matrix

Damaged measuring windows

Lacking quality of the zero adjustment, e. g. due to contaminated ultrapure 

water

The user calibration is not representative (or erroneous)

4.3

Calibration

4.3.1 Overview

In the delivery condition, the sensor is precalibrated and ready to measure (see 

section 3.4.1).
There are two types of calibration that are included into the calculation of the 

CAUTION

Never look into the measuring window or put objects into the 

measuring window during operation! The emitted UV radiation 

can damage the eyes!

In the case of authorized use, inadvertent eye contact with the 

light beam is not possible.

Raw value,

identifiable by #

Measured value

Summary of Contents for NitraVis 701 IQ TS

























































Reviews: