Xylem Flygt 5520 Installation, Operation And Maintenance Manual Download Page 36 | Manualshive

Page: 36 / 54

background image

Maintenance

Precautions

WARNING:

• Always follow safety guidelines when working on the product. See

Introduction and

• Disconnect and lock out electrical power before installing or servicing the pump.
• Make sure that the unit cannot roll or fall over and injure people or damage property.
• Rinse the unit thoroughly with clean water before working on the unit.
• Rinse the components in water after dismantling.

Make sure that you follow these requirements:

• Check the explosion risk before you weld or use electrical hand tools.
• Allow all system and pump components to cool before you handle them.
• Make sure that the product and its components have been thoroughly cleaned.
• Do not open any vent or drain valves or remove any plugs while the system is

pressurized. Make sure that the pump is isolated from the system and that pressure is
relieved before you disassemble the pump, remove plugs, or disconnect piping.

Maintenance guidelines

During maintenance and before reassembly, always remember to perform these tasks:

• Clean all parts thoroughly, particularly O-ring grooves.
• Change all O-rings, gaskets, and seal washers.
• Lubricate all springs, screws, and O-rings with grease.

During reassembly, always make sure that existing index markings are in line.
The reassembled drive unit must always be insulation-tested and the reassembled pump
must always be test-run before normal operation.

Torque values

All screws and nuts must be lubricated to achieve correct tightening torque. Screws that
are screwed into stainless steel must have the threads coated with suitable lubricants to
prevent seizing.
If there is a question regarding the tightening torques, please contact a sales
representative.

Screws and nuts

Table 1: Stainless steel, A2 and A4, torque Nm (ft-lbs)

Property

class

M4

M5

M6

M8

M10

M12

M16

M20

M24

M30

50

1.0 (0.74)

2.0 (1.5)

3.0 (2.2)

8.0 (5.9)

15 (11)

27 (20)

65 (48)

127 (93.7) 220 (162) 434 (320)

70, 80

2.7 (2)

5.4 (4)

9.0 (6.6)

22 (16)

44 (32)

76 (56)

187 (138) 364 (268) 629 (464) 1240

(915)

Maintenance

34

Flygt 5520 Installation, Operation, and Maintenance Manual

«
...
34
35
36
37
38
...
»

Summary of Contents for Flygt 5520























































Reviews:

No comments

Related manuals for Flygt 5520

Brand: Jacuzzi Pages: 8

Altherma 3 H MT ECH2O

Brand: Daikin Pages: 24

Altherma 3 H MT ECH2O

Brand: Daikin Pages: 68

Brand: Daikin Pages: 46

Brand: Daikin Pages: 24

Brand: Gamo Pages: 25

Brand: Gamma Vacuum Pages: 27

Brand: YAMADA Pages: 14

Raypak Delta Limited 399B

Brand: Rheem Pages: 67

FLOOD KING 240V

Brand: U.S. Products Pages: 8

Brand: T.I.P. Pages: 104

Brand: Jandy Pages: 24

Brand: Rosenbauer Pages: 27

Brand: GASLAND chef Pages: 60

Brand: Elite Pages: 9

Brand: Yardworks Pages: 19

Brand: Stihl Pages: 164

Brand: Wanner Engineering Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands