manualshive.com logo in svg

Xylem FLYGT 2640.181, Service And Repair Instructions, Page: 39 / 72

Share
Download
Xylem FLYGT 2640.181 Service And Repair Instructions Download Page 39

2

1

WS008551A

1. Terminal plate unit

2. Starter unit

6. Disconnect the stator leads.

4.5.11  Remove the stator

1. Lift the stator housing.
2. Place a protective material underneath to prevent the stator from breaking when

released.

3. Use an LP gas set to heat the stator housing quickly and evenly, until the stator drops.

Do not allow the stator housing temperature to exceed 150°C (302°F).

CAUTION: Thermal Hazard

Allow surfaces to cool before starting work, or wear heat-protective
clothing.

WS002667A

4. When the stator is released and has dropped down, allow the stator housing and the

stator to cool.
If the new stator is ready to be installed, then check that the stator housing is 150°C
(302°F). If it is, then install the new stator without allowing the stator housing to cool
down.

4.6  Assemble the pump

4.6.1  Assembly overview

The following flowchart shows the general workflow for assembling the pump.

Stator

↓

Electrical connections, cable entry

↓

4  Maintenance

2640.181/.281 Service and Repair Instructions

37

Summary of Contents for FLYGT 2640.181









































































Reviews:

No comments