Xylem Bell & Gossett 3DWS Instruction Manual Download Page 4

1  Introduction and Safety

1.1  Introduction

1.1.1  Purpose of the manual

The purpose of this manual is to provide necessary information for:
• Installation
• Operation
• Maintenance

WARNING:
Carefully read the Instruction Manual to avoid serious personal injury and property hazards

and to ensure safe use and proper care of this product.

NOTICE:
Save this manual for future reference, and keep it readily available at the location of the unit.

The information contained in this manual is intended to assist operating personnel by

providing information on the characteristics of the purchased equipment. It does not relieve

the user of the responsibility to adhere to local codes and ordinances and the use of

accepted practices in the installation, operation and maintenance of this equipment. Further

information pertaining to the installation, operation, and maintenance of your TechnoForce e-

MTV pump controller can be found in the IOMs for the associated equipment provided

Maintenance section for a list of relevant manuals. Equipment cannot operate well without

proper care. To keep this unit at top efficiency, follow the recommended installation and

servicing procedures outlined in this manual.

1.2  Safety

WARNING:

• The operator must be aware of safety precautions to prevent physical injury.
• Operating, installing, or maintaining the unit in any way that is not covered in this manual

could cause death, serious personal injury, or damage to the equipment. This includes

any modification to the equipment or use of parts not provided by Xylem. If there is a

question regarding the intended use of the equipment, please contact a Xylem

representative before proceeding.

• Do not change the service application without the approval of an authorized Xylem

representative.

CAUTION:
You must observe the instructions contained in this manual. Failure to do so could result in

physical injury, damage, or delays.

1.3  Safety terminology and symbols

About safety messages

It is extremely important that you read, understand, and follow the safety messages and

regulations carefully before handling the product. They are published to help prevent these

hazards:

1  Introduction and Safety

2

3DWS/4DWS Single Phase Simplex Control Panel Instruction Manual

Summary of Contents for Bell & Gossett 3DWS

















Reviews: