manualshive.com logo in svg

Xylem Aanderaa 4296, Operation Manual, Page: 55 / 109

Share
Download
Xylem Aanderaa 4296 Operation Manual Download Page 55

June 2022 – TD 320 OPERATING MANUAL – TURBIDITY SENSOR 4296

                                    Page 55

 

 

 

 

 

 

 

 

4.4.1 Control Panel 

 

In the 

Control Panel 

window you will find four tabs, 

Recorder Panel, Device Configuration 

Device Layout 

and 

System Status

.

 Under 

Recorder Panel

 

you can start and stop recordings. If 

the recorder is running first click on the 

Stop Recorder

 

as you are not allowed to configure the 

sensor when recording. For information about 

Device Layout 

and

 

System Status 

see Manual for 

SeaGuardII Platform TD303 or SmartGuard TD293. 
 

 

If the instrument is recording, 

under

 

Recorder Panel

,

 press 

Stop All Group

s

. 

The 

Control Panel

 

is controlling 

the SeaGuardII/SmartGuard 

recorder and not individual 

sensors. However the 

Recorder 

Panel

 consist of three recording 

groups where you might put 

individual sensors in each group 

to run them on different recording 

interval. See Operation Manual 

SeaGuardII / SmartGuard for 

more info. 
Under each group you can start 

the group immediately by 

Start 

Now

, or start later using the 

Start 

Delayed

 

option 

 

 

 

The layout of this menu will vary depending on the 

Recorder

 status and selections done in the 

Deployment Settings > Multi Group Recorder

 

menu. 

 

The 

Fixed Interval

 

is the recording interval for each group. The configuration of sensors in each 

group will influence on the available recording interval. If you change the configuration of one 

sensor and this cause a longer processing time the 

Fixed Interval

 

might be changed. We 

recommend that you always check the recording interval after any changes in configuration. 

Fixed Interval

 

is not applicable in the 

Recorder Panel

 

menu unless 

Selectable in recorder 

panel

 

is selected in 

Deployment Settings > Multi Group Recorder

 

menu. 

 

Start Delayed

 

is mainly used if you want to arm your instrument to start later. This can be useful if 

you configure the instrument in your office and don’t want the instrument to record before the 

instrument is installed in water. 

Start Delayed

 

can also be used to synchronize the start time for 

the three groups or between multiple instruments. 

 

See Manual for SeaGuardII Platform TD303 or SmartGuard TD293 for more information about the 

Multi Group Recorder

 

menu. 

 

 

Figure 4-6: Recorder Panel 

Summary of Contents for Aanderaa 4296














































































































Reviews:

No comments