manualshive.com logo in svg

xxter Mobotix T24, Configuration, Page: 1 / 15

Share
Download
xxter Mobotix T24 Configuration Download Page 1

 

 

 

 

Page  1  of  15  

                                                                                       

    

            Version  2.1,  9  September  2015  

   

xxter   Mobotix   intercom   configuration   

   

xxter   can   be   used   as   an   intercom   system   in   combination   with   several   Mobotix   models.   You   can   use   

the   T24   /   T25   intercom   devices   or   the   S14M   /   S15M   camera’s   in   combination   with   an   audio-­‐mount   

and   e.g.   our   intercom   kit.   More   information   about   the   separate   parts   and   options   can   be   found   in   

our   intercom   kit   product   sheet.   

   

This   manual   can   be   used   for   several   models   and   options.   For   some   specific   devices   or   options,   

specific   settings   are   required.   When   this   is   the   case,   this   is   clearly   stated.   In   general   there   are   two   

configuration   options:   

a)

  

Without   the   use   a   SIP   server,   for   a   Mobotix   in   combination   with   only   xxter   as   a   client   

b)

  

With   a   SIP   server,   for   situations   where   you   also   want   to   use   other   SIP   clients,   for   example   a   

fixed   phone   on   the   wall,   near   the   entrance   door.   

   

In   addition   to   these   options   there   are   several   other   options:   when   using   the   S14/S15   models,   are   the   

push   buttons   and   door   release   connected   to   KNX,   or   e.g.   to   a   MX-­‐OPT-­‐IO1   or   a   MX-­‐232-­‐IO-­‐Box?      

   

This   manual   will   state   when   a   specific   setting   is   needed   for   a   specific   situation,   or   when   to   skip   a   part   

because   another   option   is   used.   

   

All   screenshots   in   this   manual   are   made   with   a   S14   camera   with   firmware   version   4.21.61   installed.   

Some   screenshots   might   differ,   but   most   settings   should   be   the   same.   Please   make   sure   you   use   

xxter   firmware   version   1.9.14   or   higher.   

   
This   manual   does   not   describe   how   to   set   up   the   initial   settings   of   the   camera   and   xxter   unit,   please   

refer   to   the   appropriate   manuals   to   set   up   the   initial   IP   settings.   When   using   the   Quick   Installation   

Wizard   of   the   Mobotix   camera,   please   select   the   following   options:   Switch   the   microphone   and   

speaker   to   on,   and   select   JPEG   encoding   for   the   camera.   

   

The   configuration   and   installation   will   proceed   with   the   following   steps:   

   

1)

  

Configure   the   audio   /   video   settings   

1.1)   Configuration   for   the   Mobotix   camera   

1.2)   Configuration   for   xxter   

   

2)

  

Configure   the   push   buttons   and   the   alert   service   

2.1)   Configure   the   alert   service   

2.2)   Configure   the   push   buttons   in   the   Mobotix   

   

3)

  

Configure   the   contact   to   open   the   door   

   

4)

  

Connect   from   the   Internet   

Summary of Contents for Mobotix T24
















Reviews:

No comments