manualshive.com logo in svg

Xtramus DApps-QoS, User Manual

Share
Download
Xtramus DApps-QoS User Manual Download Page 21

 

 
 

21 

E-mail: [email protected] 

Website:  www.Xtramus.com

 

XTRAMUS TECHNOLOGIES

®

 

5. Installing/Uninstalling DApps-QoS 

Please follow the steps down below to install DApps-QoS. Also, please note that DO NOT connect your 
NuDOG-301C to your PC before DApps-QoS is properly installed on your PC. 

 

Installing DApps-QoS 

 

1.  Double-click DApps-QoS installation program 

and start the installation process

*

. 

 

2.  InstallShield Wizard is starting to install 

DApps-QoS. If you would like to cancel 
installation, click “

Cancel

”. 

 

3.  Click “

Next

” to continue installation.   

*Note: 

Due to different Operating Systems or system settings, warning messages might pop up when 

installing DApps-QoS or driver for your device. When this occurs, please choose the options on these 
pop-up warning messages that allow you to continue installing DApps-QoS or device driver.   

Summary of Contents for DApps-QoS




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands