Xtrails VESDA-E VEP-A00 Product Manual Download Page 62

Page: 62 / 109

VESDA-E VEP-A00-P Product Guide

www.xtralis.com

Command

Description

Execute From

A button

on the

Detector

Xtralis VSC

Software

Start Minor Fault Test

Generates a minor fault on the detector and de-
energizes the fault relay for 2 minutes.

Start Alarm Test

Simulates full scale smoke level which causes the
Alert, Action , Fire 1 and Fire 2 alarm conditions to
occur.

Alarm relays will energize unless the detector is
disabled.

Start Air Flow Fault Test Tests the air flow sensing system by shutting down

the aspirator.

Start Relay Test

Tests the available relays by activating and
deactivating as required.

Start LED Test

Tests each LED by cycling through all LEDs on the
detector display panel.

Return to Factory
Defaults

Restores the configuration of the detector to the
initial factory default values.

Set System Date and
Time

Sets the detector date and time.

Table 5-2: Detector Commands (continued...)

Summary of Contents for VESDA-E VEP-A00














































































































Search results

Summary of Contents for VESDA-E VEP-A00

Reviews:

Related manuals for VESDA-E VEP-A00

Brands by name

Popular brands

Xtrails VESDA-E VEP-A00, Product Manual

Search results

Summary of Contents for VESDA-E VEP-A00

Reviews:

Related manuals for VESDA-E VEP-A00

Brands by name

Popular brands