Xtrails VESDA-E VEP-A00 Product Manual Download Page 17

Page: 17 / 109

VESDA-E VEP-A00-P Product Guide

www.xtralis.com

2.7

Specifications

Specification

Value

Supply Voltage

18 to 30 VDC (24 VDC Nominal)

Power Consumption @24 VDC

Aspirator

Setting 1

Setting 5 Fixed

VEP-P

Power (Quiescent)

7.0 W

8.8 W

Power (In Alarm)

7.8 W

9.6 W

VEP-1P Power (Quiescent)

8.8 W

Power (In Alarm)

9.6 W

Dimensions (WHD)

350 mm x 225 mm x 135 mm

(13.8 in x 8.9 in x 5.3 in)

Weight

4.4 kg (9.7 lbs)

Operating Conditions

Please consult your Xtralis representative for
information on operation outside these parameters
or where sampled air is continually above 0.05%
obs/m (0.015% obs/ft) under normal operating
conditions.

Temperature:

Ambient:

0°C to 39°C (32°F to 102°F)

Sampled Air:

-20°C to 60°C (-4°F to 140°F)

Tested to:

-20°C to 55°C (-4°F to 131°F)*

* UL:-20°C to 50°C (-4°F to 122°F)

Humidity:

5-95% RH, non-condensing

Storage Conditions

(Non-operational)

Humidity:

Dry (<95%)

Temperature:

0° to 85°C

Must not be exposed to sunlight or other radiation sources

Sampling Pipe Network

Maximum length per pipe when using four straight
pipes:

Four pipe VEP-A00-P: 70 m (230 ft)

One pipe VEP-A00-1P: 100 m (328 ft)

Maximum total pipe length (with branches):

Four pipe VEP-A00-P: 560 m (1,837 ft)

One pipe VEP-A00-1P: 130 m (427 ft)

Pipe Modeling Design Tool:

ASPIRE

Refer to Section 3.1 Design Considerations.

Note:

Standards compliance of a particular pipe network
must be determined using ASPIRE.

Inlet Pipe Size

External Diameter:

25 mm or 1.05 in (3/4" IPS)

Exhaust Pipe Size

External Diameter:

25 mm or 1.05 in (3/4" IPS) via

adaptor

Relays

7 programmable relays

Contacts rated 2A @ 30 VDC (Resistive)

Programmable to latch or not latch alarm or fault states

IP Rating

IP 40

(not UL tested)

Mounting

Upright or inverted

Cable Access

4 x 26 mm (1 in) ports

Cable Termination

Screw terminal blocks (0.2-2.5 sq mm, 24-14 AWG)

Interfaces

USB (Type 2)

Ethernet (RJ45)

Table 2-2: VEP-A00 Detector Specifications

Summary of Contents for VESDA-E VEP-A00














































































































Search results

Summary of Contents for VESDA-E VEP-A00

Reviews:

Related manuals for VESDA-E VEP-A00

Brands by name

Popular brands

Xtrails VESDA-E VEP-A00, Product Manual

Search results

Summary of Contents for VESDA-E VEP-A00

Reviews:

Related manuals for VESDA-E VEP-A00

Brands by name

Popular brands