Xo XOOTR24BS Installation Instructions Manual Download Page 1

Page: 1 / 25

READ CAREFULLY

KEEP THESE INSTRUCTIONS

Installation

Over the Range

Instructions

Microwave Oven

Read these instructions completely and carefully.

•

IMPORTANT –

Save these

instructions for local inspector’s use.

•

IMPORTANT –

Observe all

governing codes and ordinances.

•

Note to Installer –

Be sure to leave these

instructions with the Consumer.

BEFORE YOU BEGIN

•

Note to Consumer –

Keep these

instructions for future reference.

• Skill level – Installation of this appliance requires

basic mechanical and electrical skills.

• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not

covered under the Warranty.

p/n A06823411

Questions? Call XO Appliance at 1-973-403-8900

March 2020

24 Eisenhower Parkway | Roseland, NJ 07068
p. 973.403.8900 | www.xoappliance.com

MODEL: XOOTR24BS

Summary of Contents for XOOTR24BS


























Search results

Summary of Contents for XOOTR24BS

Reviews:

Related manuals for XOOTR24BS

Brands by name

Popular brands

Xo XOOTR24BS, Installation Instructions Manual

Search results

Summary of Contents for XOOTR24BS

Reviews:

Related manuals for XOOTR24BS

Brands by name

Popular brands