XMA Viglen Omnino Pro Assembly Manual Download | Manualshive

Page: 40 / 60

background image

0115 846 4000

[email protected]

© 2019 XMA Ltd. All Rights Reserved

15 Removing Internal Power board

Procedure

1.  Disconnect the 19V power cable (4Pin converter to 2Pin DC cable) from the system board.
2.  Lift the mylar from the power board.
3.  Remove the screws that secure the power board to the computer base.
4.  Remove the two screws from outlet connector.
5.  Lift the power board, along with its cable, off the computer base.

4PIN convert to 2PIN DC cable

NOTE: Please ensure 4Pin converter to 2Pin DC cable is used, this cable should not be discarded.

«
...
38
39
40
41
42
...
»

Summary of Contents for Viglen Omnino Pro





























































Reviews:

No comments

Related manuals for Viglen Omnino Pro

Brand: Stahl Pages: 24

d260 - Microtower Desktop PC

Brand: Compaq Pages: 1

Eee Top ET16 Series

Brand: Asus Pages: 34

Brand: Asus Pages: 3

Brand: Asus Pages: 46

Brand: Asus Pages: 60

Brand: Asus Pages: 86

Brand: Asus Pages: 50

Brand: Asus Pages: 40

Brand: Asus Pages: 38

Brand: Asus Pages: 46

Brand: Asus Pages: 95

Brand: Asus Pages: 50

Brand: Asus Pages: 70

Brand: Asus Pages: 38

DiGiMatrix AB-V100

Brand: Asus Pages: 112

Brand: Asus Pages: 62

Brand: Asus Pages: 61

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands