XMA Viglen Omnino Pro Assembly Manual Download | Manualshive

Page: 29 / 60

background image

0115 846 4000

[email protected]

© 2019 XMA Ltd. All Rights Reserved

10.1 Removing the Rear cover (Part 2)

Procedure

1.

Prepare the computer for disassembly (see Important Safety Instructions).

2.

Using caution, lay the Omnino Pro down on a flat surface covered with a soft cloth.

3.

Remove the screws that secure the base cover.

4.

Gently lift the back cover ensuring to disconnect webcam module connector from the system board.

«
...
27
28
29
30
31
...
»

Summary of Contents for Viglen Omnino Pro





























































Reviews:

No comments

Related manuals for Viglen Omnino Pro

Brand: Gateway Pages: 126

Brand: CompuLab Pages: 19

Brand: Tandy Pages: 138

Brand: IBM Pages: 158

Brand: EUROCOM Pages: 113

TRS-80 Model 100

Brand: Radio Shack Pages: 210

Brand: GREER Company Pages: 18

Brand: Dell Pages: 70

Brand: Packard Bell Pages: 13

Brand: Packard Bell Pages: 15

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

VAIO VPCF127FXB

Brand: Sony Pages: 3

VAIO VPCF121FXH

Brand: Sony Pages: 3

VAIO VPCF120FDB

Brand: Sony Pages: 2

VAIO VPCF11JFX/B

Brand: Sony Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands