background image

XT6264 User Guide 
 

P a g e  

2 | 14

 

CONFIDENTIAL AND PROPRIETARY 

Disclosure, storage and use subject to non-disclosure agreement

 

 

1

 

C

ONTENTS

 

Contents ................................................................................................................................................ 2 

Installation Procedure ........................................................................................................................... 3 

2.1 

Terminology .................................................................................................................................. 3 

2.2 

Installation .................................................................................................................................... 3 

2.3 

Testing After Installation ............................................................................................................... 7 

LED Behavior ......................................................................................................................................... 8 

3.1 

Test Mode ..................................................................................................................................... 8 

3.1.1 

LED Color Table ..................................................................................................................... 8 

3.1.2 

RCD3 LED Status Indication Mode ........................................................................................ 8 

3.2 

Install Mode ................................................................................................................................ 11 

3.2.1 

Entering Install Mode .......................................................................................................... 11 

3.2.2 

Install Mode Operation and Status ..................................................................................... 11 

3.2.3 

Exiting Install Mode ............................................................................................................. 11 

Regulatory Statements ....................................................................................................................... 12 

4.1 

FCC: ............................................................................................................................................. 12 

4.2 

Radiofrequency radiation exposure Information: ...................................................................... 12 

4.3 

IC ................................................................................................................................................. 12 

 

Summary of Contents for XT6264















Reviews: