Xime PB-X1000, User Manual

Page: 11 / 12

20 21
Others
PB-X800 / PB-X1000 / PB-X1500 / PB-X2000 / PB-X2500
AC 230V 50Hz
Max. 580W
1.5m (length)
98-735kPa, 0.7~7.5kgf/
? ?
? ?
? ? ?
? ?
? ? ?
?@6Xe? ?(R1e?
J@e? ?W&@e?
O&@5e? W2@@@6T2@@@@@He? 7<e@@@<?@e@?e?
?J5?e@@5??@e@?e? ?7H?e3@H??@e@?e?
?@fN@e?@e@?e? ?@f?@e?@e@?e?
?3L?eJ@e?@e@?e? ?V/K?O&@L?J@L?@Le? V4@0R4@?@@@?@@e?
? ?
? ? ?
? ?
483(width) x 530(depth) x 137(height)
5kg
Max. 1.1min. Water Stream Angle 55°, Self-cleaning Type
Max. 1.3min. Water Stream Angle 55°, Self-cleaning Type
Move and Massage Functions, Position Adjustment
4-level adjustment each of Anal Cleaning and Bidet
(Very Weak, Weak, Medium, Strong), Mycom Control
4-level adjustment (OFF, Low:33 , Medium: 37 , High: 41 )
530W
1.2 liter
4-level adjustment (OFF, Low:34 , Medium: 38 , High: 42 )
50W
Damper (Slowdown) function
4-level adjustment (Room, Low:35 , Medium: 40 , High: 45 )
250W
Catalysis type
PRODUCT NAME
MODEL
RATING
POWER CONSUMPTION
POWER CORD
SUPPLYING WATER PRESSURE
DIMENSION (mm)
WEIGHT
ANAL CLEANING
BIDET
WATER PRESSURE
ADJUSTMENT
TEMPERATURE
ADJUSTEMENT
POWER CONSUMPTION OF
WATER HEATER
TANK CAPACITY
TEMPERATURE
ADJUSTMENT
POWER CONSUMPTION
OF HEATER
OTHERS
TEMPERATURE
ADJUSTMENT
POWER CONSUMPTION
OF HEATER
WARM
WATER
CLEANSER
TOILET
SEAT
HEATER
WARM
AIR
DRYER
DEODORIZER
Automatic Cleansing & Drying Toilet
Can not operate the Bidet at all
Is the power plug not loose?
Power failure perhaps?
No water stream
Check if the water supply valve (water tap) is open
Is the nozzle not blocked?
Check if the water filter of the water supply valve (Bidet) is not blocked.
No water supply perhaps?
If the Bidet is used for the first time after the installation, it takes 1~2
minutes until the water fills the tank before it begins to flow out.
Water stream is very weak
Check the indicator lamp to see if the water pressure setting is too low.
Open the filter cap and check the filter.
Close the other water taps to improve the water flow.
Warm water is not warm enough
Isn’t the WATER TEMPERATURE button set to “OFF”
The capacity of the warm water tank is for about 1 minute’s use after
which the water is no longer warm and it will take about 7 minutes
until the water is warmed up again to the set temperature.
Water leaks
Fasten the connection of the water supply hose again
Check all the connection parts. Especially see if any rubber stopper
is missing.
Warm air or the toilet seat is not warm enough
Isn’t the temperature adjustment button of
DRY or TOILET SEAT set to “OFF”?
Water drips while not in use
If the water in the warm water tank is heated
up, it expands and seeps through the nozzle.
Water spray activated before and after the use
is to clean the nozzle and is normal.