Xilinx Virtex-5 FPGA ML561 Page 52 User Manual Download | Manualshive

Page: 52 / 385

background image

52

Virtex-5 FPGA User Guide

UG190 (v5.0) June 19, 2009

Chapter 2:

Clock Management Technology

Feedback Clock Input - CLKFB

The feedback clock (CLKFB) input pin provides a reference or feedback signal to the DCM
to delay-compensate the clock outputs, and align them with the clock input. To provide the
necessary feedback to the DCM, connect only the CLK0 DCM output to the CLKFB pin.
When the CLKFB pin is connected, all clock outputs are deskewed to CLKIN. When the
CLKFB pin is not connected, DCM clock outputs are not deskewed to CLKIN. However,
the relative phase relationship between all output clocks is preserved.

During internal feedback configuration, the CLK0 output of a DCM connects to a global
buffer on the same top or bottom half of the device. The output of the global buffer
connects to the CLKFB input of the same DCM.

During the external feedback configuration, the following rules apply:

1.

To forward the clock, the CLK0 of the DCM must directly drive an OBUF or a BUFG-
to-DDR configuration.

2.

External to the FPGA, the forwarded clock signal must be connected to the IBUFG
(GCLK pin) or the IBUF driving the CLKFB of the DCM. Both CLK and CLKFB should
have identical I/O buffers.

illustrates clock forwarding with external feedback configuration.

The feedback clock input signal can be driven by one of the following buffers:

1.

IBUFG – Global Clock Input Buffer

This is the preferred source for an external feedback configuration. When an IBUFG
drives a CLKFB pin of a DCM in the same top or bottom half of the device, the pad to
DCM skew is compensated for deskew.

2.

BUFGCTRL – Internal Global Clock Buffer

This is an internal feedback configuration driven by CLK0.

3.

IBUF – Input Buffer

This is an external feedback configuration. When IBUF is used, the PAD to DCM input
skew is not compensated and performance can not be guaranteed.

Phase-Shift Clock Input - PSCLK

The phase-shift clock (PSCLK) input pin provides the source clock for the DCM phase
shift. The PSCLK can be asynchronous (in phase and frequency) to CLKIN. The phase-shift
clock signal can be driven by any clock source (external or internal), including:

1.

IBUF – Input Buffer

2.

IBUFG – Global Clock Input Buffer

To access the dedicated routing, only the IBUFGs on the same half of the device (top or
bottom) as the DCM can be used to drive a PSCLK input of the DCM.

3.

BUFGCTRL – An Internal Global Buffer

4.

Internal Clock – Any internal clock using general purpose routing.

The frequency range of PSCLK is defined by PSCLK_FREQ_LF/HF. See the

Virtex-5 FPGA

Data Sheet

. This input must be tied to ground when the CLKOUT_PHASE_SHIFT attribute

is set to NONE or FIXED.

«
...
50
51
52
53
54
...
»

Summary of Contents for Virtex-5 FPGA ML561


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Virtex-5 FPGA ML561

Brand: Barco Pages: 121

HHM Series HHM2411

Brand: TDK Pages: 2

Brand: OpenVox Pages: 13

Brand: UNA AUTOMATION Pages: 20

IMACS Network Device

Brand: Zhone Pages: 114

Brand: Compro Technology Pages: 2

Brand: Abit Pages: 22

Suzie-Q 541.35.520

Brand: Hafele Pages: 12

Brand: Cypress Semiconductor Pages: 38

Brand: ANTAIRA Pages: 6

Brand: Adaptec Pages: 2

X-NUCLEO-AMICAM1

Brand: ST Pages: 18

Compressor DW-CP04

Brand: Digital Watchdog Pages: 73

Brand: National Datacomm Pages: 62

HYPER-BT-E38 1 Series

Brand: IEI Technology Pages: 95

i.MX 6SoloLite Linux

Brand: Freescale Semiconductor Pages: 199

Brand: soundsation Pages: 47

Brand: Pico Macom Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands