manualshive.com logo in svg

Xilinx Virtex-5 FPGA ML561, User Manual

The Xilinx Virtex-5 FPGA ML561 offers outstanding performance and versatility for advanced electronic designs. For convenient usage, a comprehensive User Manual is available for free download at manualshive.com. This manual provides detailed instructions and valuable insights, ensuring seamless integration and successful implementation of this cutting-edge product.

Share
Download
background image

Virtex-5 FPGA User Guide

www.xilinx.com

319

UG190 (v5.0) June 19, 2009

ILOGIC Resources

The SRVAL attributes can be set individually for each storage element in the ILOGIC block, 
but the choice of synchronous or asynchronous set/reset (SRTYPE) can not be set 
individually for each storage element in the ILOGIC block.

The following sections discuss the various resources within the ILOGIC blocks. All 
connections between the ILOGIC resources are managed in Xilinx software.

Combinatorial Input Path

The combinatorial input path is used to create a direct connection from the input driver to 
the FPGA fabric. This path is used by software automatically when:

1.

There is a direct (unregistered) connection from input data to logic resources in the 
FPGA fabric.

2.

The "pack I/O register/latches into IOBs" is set to OFF.

Input DDR Overview (IDDR)

Virtex-5 devices have dedicated registers in the ILOGIC to implement input double-data-
rate (DDR) registers. This feature is used by instantiating the IDDR primitive. 

There is only one clock input to the IDDR primitive. Falling edge data is clocked by a 
locally inverted version of the input clock. All clocks feeding into the I/O tile are fully 
multiplexed, i.e., there is no clock sharing between ILOGIC and OLOGIC blocks. The 
IDDR primitive supports the following modes of operation:

•

OPPOSITE_EDGE mode

•

SAME_EDGE mode

•

SAME_EDGE_PIPELINED mode

The SAME_EDGE and SAME_EDGE_PIPELINED modes are the same as for the Virtex-4 
architecture. These modes allow designers to transfer falling edge data to the rising edge 
domain within the ILOGIC block, saving CLB and clock resources, and increasing 
performance. These modes are implemented using the DDR_CLK_EDGE attribute. The 
following sections describe each of the modes in detail.

OPPOSITE_EDGE Mode

A traditional input DDR solution, or OPPOSITE_EDGE mode, is accomplished via a single 
input in the ILOGIC. The data is presented to the fabric via the output Q1 on the rising 
edge of the clock and via the output Q2 on the falling edge of the clock. This structure is 
similar to the Virtex-II, Virtex-II Pro, and Virtex-4 FPGA implementation. 

Figure 7-2

 shows 

the timing diagram of the input DDR using the OPPOSITE_EDGE mode.

Table 7-2:

Truth Table when SRVAL = 1

SR

REV

Function

0

0

NOP

0

1

Set

1

0

Reset

1

1

Reset

Summary of Contents for Virtex-5 FPGA ML561


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Virtex-5 FPGA ML561

Cabletron Systems Netlink FRX8000 Installation And Setup Manual preview
Netlink FRX8000
Brand: Cabletron Systems Pages: 94
Cabletron Systems MMAC-Plus 9E423-24 Reference Manual preview
MMAC-Plus 9E423-24
Brand: Cabletron Systems Pages: 10
Cabletron Systems MMAC-Plus 9A128-01 Management Manual preview
MMAC-Plus 9A128-01
Brand: Cabletron Systems Pages: 22
Cabletron Systems Spectrum EMM-E6 Addendum Manual preview
Spectrum EMM-E6
Brand: Cabletron Systems Pages: 2
Cabletron Systems DLM6C-AA Overview And Setup Manual preview
DLM6C-AA
Brand: Cabletron Systems Pages: 54
Cabletron Systems Cabletron BRIM-F6 User Manual preview
Cabletron BRIM-F6
Brand: Cabletron Systems Pages: 43
Cabletron Systems Netlink FRX4000 Maintenance Manual preview
Netlink FRX4000
Brand: Cabletron Systems Pages: 60
Cabletron Systems 9E132-15 Appendix preview
9E132-15
Brand: Cabletron Systems Pages: 8
Cabletron Systems TRXI-22 Addendum preview
TRXI-22
Brand: Cabletron Systems Pages: 4
TC Electronic ATAC Service Manual preview
ATAC
Brand: TC Electronic Pages: 55
RadiSys EPC-31 Hardware Reference Manual preview
EPC-31
Brand: RadiSys Pages: 44
IBA ibaFOB-4i-X Manual preview
ibaFOB-4i-X
Brand: IBA Pages: 33
Xantech CC12 Installation Instructions preview
CC12
Brand: Xantech Pages: 4
Wyse C90LE7 Quick Start Manual preview
C90LE7
Brand: Wyse Pages: 8
ORiNG PCard-E 021L-D5 Series Quick Installation Manual preview
PCard-E 021L-D5 Series
Brand: ORiNG Pages: 2
Datum bc635VME Operation And Technical Manual preview
bc635VME
Brand: Datum Pages: 49
Cowlacious Designs ISD CAP 275 Manual preview
ISD CAP 275
Brand: Cowlacious Designs Pages: 8
Renesas RL78/L1C User Manual preview
RL78/L1C
Brand: Renesas Pages: 4

Brands by name

Popular brands

Load more brands