manualshive.com logo in svg

Xilinx Virtex-5 FPGA ML561, User Manual

Share
Download
Xilinx Virtex-5 FPGA ML561 User Manual Download Page 166

166

www.xilinx.com

Virtex-5 FPGA User Guide

UG190 (v5.0) June 19, 2009

Chapter 4:

Block RAM

Standard ECC

Set by Attributes

EN_ECC_READ = TRUE
EN_ECC_WRITE = TRUE

Standard ECC Write

At time T1W, DI[63:0] = A is written into memory location 

a

. The corresponding 8 bits of 

ECC parity PA (hex) are generated internally, appended to the 64 data bits, and written into 
the memory. Immediately after the write, the parity value PA appears at output 
ECCPARITY[7:0]. Since ECC parity is generated internally, DIP[7:0] pins are not used.

Similarly, at time T2W and T3W, DI[63:0] = B and C, together with their corresponding 
parity bits PB (hex) and PC (hex) are written into memory locations 

b

 and 

c

. PB and PC 

appear at output ECCPARITY[7:0] shortly after T2W and T3W.

Standard ECC Read

At time T1R, the 72-bit memory content, consisting 64 bits of data A and 8 bits of parity PA 
(hex), of address location

 a 

is read and decoded internally. If there is no error, the original 

data and parity are output at DO[63:0] and DOP[7:0]. If there is a single-bit error in either 
the data or the parity, the error is corrected, and SBITERR is High. If there is a double-bit 
error in the data and parity, the error is not corrected. The original data and parity is output 
and DBITERR is High.

If attribute DO_REG is set to 0, DO[63:0] = A and DOP[7:0] = PA shortly after T1R. 
Similarly, at time T2R and T3R, the memory content at address locations

 b 

and 

c

 are read 

and decoded at DO[63:0] and DOP[7:0]. SBITERR/DBITERR outputs can also switch after 
T1R if a single or double-bit error is detected on dataset A. 

Figure 4-32

 shows a single-bit 

error (SBITERR) being detected on data A in latch mode after clock edge T1R and a double-
bit error (DBITERR) being detected on data B in latch mode after clock edge T2R.

If attribute DO_REG is set to 1, DO[63:0] = A and DOP[7:0] = PA shortly after T2R. 
Similarly, at time T3R and T4R, the memory content at address locations 

b 

and 

c

 are read 

and decoded at DO[63:0] and DOP[7:0]. SBITERR/DBITERR outputs may also switch after 
T2R if a single or double-bit error is detected on dataset A. 

Figure 4-32

 shows a single-bit 

error (SBITERR) being detected on data A in register mode after clock edge T2R and a 
double-bit error (DBITERR) being detected on data B in register mode after clock edge T3R.

In ECC mode, the encode-only port and the decode-only port operate independently of 
each other.

ECC Encode-Only

Set by Attributes

EN_ECC_READ = FALSE
EN_ECC_WRITE = TRUE

ECC Encode-Only Write

At time T1W, DI[63:0] = A is written into memory location a. The corresponding 8 bits of 
ECC parity PA (hex) are generated internally, appended to the 64 data bits, and written into 
the memory. Immediately after the write, the parity value PA appears at output 
ECCPARITY[7:0]. Since ECC parity is generated internally, DIP[7:0] pins are not used.

Summary of Contents for Virtex-5 FPGA ML561


































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands