manualshive.com logo in svg

Xilinx Virtex-5 FPGA ML561, User Manual

The Xilinx Virtex-5 FPGA ML561 offers outstanding performance and versatility for advanced electronic designs. For convenient usage, a comprehensive User Manual is available for free download at manualshive.com. This manual provides detailed instructions and valuable insights, ensuring seamless integration and successful implementation of this cutting-edge product.

Share
Download
background image

156

www.xilinx.com

Virtex-5 FPGA User Guide

UG190 (v5.0) June 19, 2009

Chapter 4:

Block RAM

Clock Event 3: Read Operation and Assertion of Read Error Signal

The read error signal pin is asserted when there is no data to be read because the FIFO is in 
an empty state.

•

Read enable remains asserted at the RDEN input of the FIFO.

•

At time T

FCKO_RDERR

, after clock event 3 (RDCLK), read error is asserted at the 

RDERR output pin of the FIFO.

•

Data 04 remains unchanged at the DO outputs of the FIFO.

Clock Event 4: Read Operation and Deassertion of Read Error Signal

The read error signal pin is deasserted when a user stops trying to read from an empty 
FIFO.

•

At time T

FCCK_RDEN

, before clock event 4 (RDCLK), read enable is deasserted at the 

RDEN input of the FIFO.

•

At time T

FCKO_RDERR

, after clock event 4 (RDCLK), read error is deasserted at the 

RDERR output pin of the FIFO.

The read error signal is asserted/deasserted at every read-clock positive edge. As long as 
both the read enable and empty signals are true, read error will remain asserted.

Case 5: Resetting All Flags

When the reset signal is asserted, all flags are reset.

•

At time T

FCO_EMPTY

, after reset (RST), empty is asserted at the EMPTY output pin of 

the FIFO.

•

At time T

FCO_AEMPTY

, after reset (RST), almost empty is asserted at the AEMPTY 

output pin of the FIFO.

•

At time T

FCO_FULL

, after reset (RST), full is deasserted at the FULL output pin of the 

FIFO.

•

At time T

FCO_AFULL

, after reset (RST), almost full is deasserted at the AFULL output 

pin of the FIFO.

Reset is an asynchronous signal used to reset all flags. Hold the reset signal High for three 
read and write clock cycles to ensure that all internal states and flags are reset to the correct 
value.

X-Ref Target - Figure 4-25

Figure 4-25:

Resetting All Flags

ug190_4_22_032506

WRCLK

RST

RDCLK

EMPTY

AEMPTY

FULL

AFULL

T

FCO_EMPTY

T

FCO_AEMPTY

T

FCO_FULL

T

FCO_AFULL

Summary of Contents for Virtex-5 FPGA ML561


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Virtex-5 FPGA ML561

Alesis QUADRAVERB Reference Manual preview
QUADRAVERB
Brand: Alesis Pages: 61
Tandberg Data Storagelibrary T24 Manual preview
Storagelibrary T24
Brand: Tandberg Data Pages: 28
IBA ibaFOB-4i-X Manual preview
ibaFOB-4i-X
Brand: IBA Pages: 33
Eaton APS6-400 Series Installation And Operation Manual preview
APS6-400 Series
Brand: Eaton Pages: 114
National Instruments FieldPoint cFP-RTD-122 Operating Instructions Manual preview
FieldPoint cFP-RTD-122
Brand: National Instruments Pages: 15
Promise Technology FastTrak TX4000 User Manual preview
FastTrak TX4000
Brand: Promise Technology Pages: 76
ZoneVu ZSI-450-IP Installation Manual & User Manual preview
ZSI-450-IP
Brand: ZoneVu Pages: 15
FUNcube Dongle Pro User Manual preview
Dongle Pro
Brand: FUNcube Pages: 23
LaCie FireWire 800 ExpressCard 34 Quick Install Manual preview
FireWire 800 ExpressCard 34
Brand: LaCie Pages: 24
ADLINK Technology cPCIS-1100 Series User Manual preview
cPCIS-1100 Series
Brand: ADLINK Technology Pages: 48
Cypress Semiconductor CY8C24223A Specification Sheet preview
CY8C24223A
Brand: Cypress Semiconductor Pages: 31
ALIBI ALI-NVR71128R User Manual preview
ALI-NVR71128R
Brand: ALIBI Pages: 232
BSS Audio Soundweb 9088ii DSP System    Brochure & Specs preview
Soundweb 9088ii DSP System   
Brand: BSS Audio Pages: 2
RAK RAK1901 Quick Start Manual preview
RAK1901
Brand: RAK Pages: 14
ATEN Altusen SN0100 Series User Manual preview
Altusen SN0100 Series
Brand: ATEN Pages: 178
XMOS XK-XMP-64 Hardware Manual preview
XK-XMP-64
Brand: XMOS Pages: 10
JETWAY 939GT2-Ultra Series User Manual preview
939GT2-Ultra Series
Brand: JETWAY Pages: 55
8e6 Technologies Threat Analysis Reporter TAR HL/SL/MSA Evaluation Manual preview
Threat Analysis Reporter TAR HL/SL/MSA
Brand: 8e6 Technologies Pages: 22

Brands by name

Popular brands

Load more brands