manualshive.com logo in svg

Xilinx Virtex-4 RocketIO, User Manual

Share
Download
Xilinx Virtex-4 RocketIO User Manual Download Page 13

Embedded Tri-Mode Ethernet MAC User Guide

www.xilinx.com

13

UG074 (v2.2) February 22, 2010

R

Preface

About This Guide

This document is the Virtex®-4 FPGA Embedded Tri-Mode Ethernet MAC User Guide.

Guide Contents

This user guide contains the following chapters:

•

Chapter 1, “Introduction,”

 introduces the Virtex-4 FPGA Embedded Tri-Mode 

Ethernet MAC and summarizes its features.

•

Chapter 2, “Ethernet MAC Architecture,”

 describes the architecture of the Ethernet 

MAC and defines its signals.

•

Chapter 3, “Client, Host, and MDIO Interfaces,”

 provides design information for the 

client, host, and MDIO interfaces.

•

Chapter 4, “Physical Interface,”

 describes design considerations for the supported 

interfaces when using the Ethernet MAC.

•

Chapter 5, “Miscellaneous Functions,”

 provides useful information for designing 

with the Ethernet MAC.

•

Chapter 6, “Use Models,”

 describes some available models and how to interface the 

Ethernet MAC to a processor DCR or an FPGA statistics block.

•

Chapter 7, “Using the Embedded Ethernet MAC,”

 describes the Verilog and VHDL 

CORE Generator™ wrappers.

•

Appendix A, “Ethernet MAC Timing Model,”

 provides details on the timing 

parameters of the Ethernet MAC timing model.

Additional Resources

For additional information, go to 

http://www.xilinx.com/support

. 

www.BDTIC.com/XILINX

Summary of Contents for Virtex-4 RocketIO

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands