manualshive.com logo in svg

Xilinx Virtex-4 RocketIO, User Manual

Share
Download
Xilinx Virtex-4 RocketIO User Manual Download Page 118

118

www.xilinx.com

Embedded Tri-Mode Ethernet MAC User Guide

UG074 (v2.2) February 22, 2010

Chapter 4:

Physical Interface

R

An IDELAY is used to generate 2 ns of skew required between RGMII_TXC_# and 
RGMII_TXD_# at the pin level. To access the IDELAY component, the 
EMAC#CLIENTTXGMIIMIICLKOUT signal is routed to an unused IOB configured as an 
IOBUF. The T control pin of the IOBUF is tied to ground to loop the clock back to the 
IDELAY. The IDELAY setting can be used to shift the clock through the data. The output of 
the IOB must not be connected to an external signal.

The EMAC#CLIENTTXCLIENTCLKOUT output port connects to the 
CLIENTEMAC#TXCLIENTCLKIN input port and transmitter client logic in the FPGA 
fabric through a BUFG. The receiver client clocking is similar.

Figure 4-14:

Tri-Mode RGMII v2.0 Clock Management

EMAC#

PHYEMAC#GTXCLK

CLIENTEMAC#TXGMIIMIICLKIN

EMAC#CLIENTTXGMIIMIICLKOUT

CLIENTEMAC#TXCLIENTCLKIN

EMAC#CLIENTTXCLIENTCLKOUT

EMAC#PHYTXD[3:0]

EMAC#PHYTXD[7:4]

PHYEMAC#MIITXCLK

CLIENTEMAC#DCMLOCKED

CLIENTEMAC#RXCLIENTCLKIN

EMAC#CLIENTRXCLIENTCLKOUT

GTX_CLK

TX Client
   Logic

RX Client
   Logic

BUFG

BUFG

OBUF

ODDR

D1

D2

Q

RGMII_TXD_#[3:0]

UG074_3_78_031009

BUFG

IDELAY

RGMII_IOB_#

OBUF

RGMII_TXC_#

IOBUF

(1)

No Connection

PHYEMAC#RXCLK

PHYEMAC#RXD[3:0]

PHYEMAC#RXD[7:4]

RGMII_RXD

_#

[3:0]

IBUF

Q1

Q2

D

Notes: 
1) A regional buffer (BUFR) can replace this BUFG. 
    Refer to the Virtex-4 User Guide for BUFR usage guidelines.

CLKIN

CLKFB

DCM

CLK0

SPEED_IS_10_100

BUFGMUX

RGMII_RXC_#

IBUFG

0

1

www.BDTIC.com/XILINX

Summary of Contents for Virtex-4 RocketIO

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands