background image

1. Enter the following command.

$ sudo lspci -vd 10ee:

2. If the card is successfully installed and found by the operating system, you will see a message

similar to the following.

af:00.0 Processing accelerators: Xilinx Corporation Device 5058

Subsystem: Xilinx Corporation Device 000e

Flags: bus master, fast devsel, latency 0, NUMA node 1

Memory at 39bff2000000 (64-bit, prefetchable) [size=32M]

Memory at 39bff4040000 (64-bit, prefetchable) [size=256K]

Capabilities: <access denied>

Kernel driver in use: xclmgmt

Kernel modules: xclmgmt

af:00.1 Processing accelerators: Xilinx Corporation Device 5059

Subsystem: Xilinx Corporation Device 000e

Flags: bus master, fast devsel, latency 0, IRQ 188, NUMA node 1

Memory at 39bff0000000 (64-bit, prefetchable) [size=32M]

Memory at 39bff4000000 (64-bit, prefetchable) [size=256K]

Memory at 39bfe0000000 (64-bit, prefetchable) [size=256M]

Capabilities: <access denied>

Kernel driver in use: xocl

Kernel modules: xocl

NoteFor each card, there will be two physical functions found: management and user. For additional
details, see 

XRT and Vitis Platform Overview

.

Confirm Firmware Installation

When a card has successfully been installed and the firmware has been updated, both entries for

Platform

 and 

SC version

 installed on the card and the system must match. If they do not

match, the system will be unable to correctly run applications on your card.

To confirm they match, run the following command and visually compare the 'Platform' and 'SC
Version' entries under 

Flashable partitions running on FPGA

 and 

Flashable

partitions installed in system match

.

$ sudo /opt/xilinx/xrt/bin/xbmgmt examine --device <management BDF>

To obtain the device management BDF, see 

Displaying Card BDF Values

.

In the following example output, 

Platform

 (

xilinx_u55n_gen3x4_xdma_base_1

) and 

SC

version

 (

7.1.12

) are displayed under 

Flashable partitions running on FPGA

 and

Flashable partitions installed in system

 both match.

----------------------------------------------------

1/1 [0000:af:00.0] : xilinx_u55n_gen3x4_xdma_base_1

----------------------------------------------------

Flash properties

Type : spi

Chapter 5: Card Bring-Up and Validation

UG1525 (v1.1) March 8, 2022

 

www.xilinx.com

Varium C1100 Compute Adaptor Installation Guide

 18

Send Feedback

Summary of Contents for Varium C1100



























Reviews: