Xilinx LogiCORE MicroBlaze Product Manual Download Page 31

Page: 31 / 64

MicroBlaze Micro Controller System v1.3

www.xilinx.com

PG048 December 18, 2012

Chapter 4:

Customizing and Generating the Core

This flow shows the specific steps required to implement a project with the MicroBlaze MCS

in Vivado, and the relationship between the hardware and software tools.

• Associate ELF Files:

This is the only manual step in Vivado, performed by selecting

Tools > Associate ELF

Files...

in the menu. Initially, the default infinite loop ELF file,

mb_bootloop_le.elf

, is

associated with the MicroBlaze MCS core. ELF files for implementation and simulation

are specified separately.

Note:

The associated ELF files are imported into the project. This means that they are unaffected

by changes during software development in SDK, but need to be re-imported to apply any

changes.

The final bitstream updated with software is named download.bit, and is normally located

in the project directory

project-name.runs/impl_1

For additional information, see the

Xilinx Vivado Manuals

[Ref 9]

SDK

The SDK commands to achieve the MicroBlaze MCS specific steps above are detailed here:

• Import Hardware Description - For each MicroBlaze MCS component to import:

Select

File > New > Project...

in the menu.

Expand

Xilinx

, and select

Hardware Platform Specification

Click

Next

Click

Browse

, and navigate to the hardware description file:

- In PlanAhead™ this file is typically called

project-name.srcs/sources_1/

ip/component-name/component-name_sdk.xml

- In Project Navigator this file is typically called

ipcore_dir/

component-name_sdk.xml

Click

Finish

to perform the import.

After the hardware description has been imported, a standalone board support package

can be created, which provides MicroBlaze processor-specific code, and the I/O Module

software driver. The MicroBlaze MCS configuration is available in the generated file

microblaze_0/include/xparameters.h

• Import Hardware Implementation:

Select

Xilinx Tools > Program FPGA

in the menu.

Click the first

Browse

button, and navigate to the bitstream:

Summary of Contents for LogiCORE MicroBlaze

































































Search results

Summary of Contents for LogiCORE MicroBlaze

Reviews:

Brands by name

Popular brands

Xilinx LogiCORE MicroBlaze, Product Manual

Search results

Summary of Contents for LogiCORE MicroBlaze

Reviews:

Brands by name

Popular brands