manualshive.com logo in svg

Xilinx LogiCORE IP, Product Manual

Share
Download
Xilinx LogiCORE IP Product Manual Download Page 109

XAUI v12.3 Product Guide

www.xilinx.com

109

PG053 April 6, 2016

Chapter 7:

Design Flow Steps

Output Generation

For details, see “Generating IP Output Products” in the 

Vivado Design Suite User Guide: 

Designing with IP

 (UG896) 

[Ref 5]

.

Constraining the Core

This section contains information about constraining the core in the Vivado Design Suite.

Required Constraints

This section defines the constraint requirements for the core. Constraints are provided with 

an XDC file. An XDC is provided with the HDL example design to give a starting point for 

constraints for the user design. The following constraints are required.

Constraints specific to the core are applied by the Vivado® Design Suite. A hierarchical XDC 

is applied to the core that will apply the necessary clock constraints. System-level 

constraints such as DCLK frequency and Transceiver location should be applied in the user 

XDC.

Clock Frequencies

A constraint specifying the frequency of the clock (156.25 MHz for 10G or 312.5 MHz for 

20G) is already set in the hierarchical XDC file. This clock is being sourced from the 

txoutclk

 port of one of the transceivers inside the core.

DCLK clock must be provided and a constraint is required to specify its frequency:

create_clock -name dclk -period 20.000 [get_ports dclk]

Transceiver Type

vu_gt_type

GTHE3

Transceiver reference clock frequency 

(MHz)

RefClkRate

156.25

XAUI lane 0 transceiver location

Locations 

X0Y0

DRP Clock Frequency (MHz)

DRPCLK_FREQ

50.0

1. Parameter values are listed in the table where the GUI parameter value differs from the user parameter value. Such 

values are shown in this table as indented below the associated parameter.

Table 7

‐

1:

GUI Parameter to User Parameter Relationship 

(Cont’d)

GUI Parameter/Value

(1)

User Parameter/Value

(1)

Default Value

Send Feedback

Summary of Contents for LogiCORE IP















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands