State
Common Problem(FAQ)
Bluetooth Se�ngs
Interface Se�ngs
Scanning Mode Se�ng
（
2
）
USB Virtual Serial Port
（
3
）
Bluetooth
Set the bluetooth power on/off �me
Always on
Scan mode se�ngs by scanning the barcode below.
(1)Manual Mode
(2)Sensing Mode
(3)Con�nuous Mode
▲
▲
Offline Mode
▲
Others
(2)Send the offline data
(1)Aiming Barcode
ON
OFF
(2)Read Successfully Barcode
ON
OFF
ON
OFF
The scanner can communicate with the host by RS-232 serial port
or USB port. The user can switch to the corresponding interface by
replacing the data line and scanning the corresponding barcode
below.
（
1
）
USB Virtual Keyboard
5mins
10mins
15mins
30mins
60mins
(3)Clear the offline data
(4)Display the quality of offline storage
(1)Offline storage
Q
：
There are some barcodes can not be scanned.
A
：
a) Firstly, check the barcode type, open the barcode func�on; if it is
verified, try to turn off.
b) Unable to know the barcode type, then set all barcodes allowed to
be recognized.
Q
：
The barcode data is incorrect.
A
：
Check the error display of barcodes (all barcodes errors or specific
barcode error)
Q
：
Barcode can be recognized but not displayed.
A
：
Firstly, confirm the scanner whether it is in the Bluetooth transfering
mode. If yes, the scanner has been connected to the PC.
Q
：
Aiming Light and LED are not bright.
A
：
a) Check whether the device is powered on.
b) Re-plug the data cable.
Our company does not assume any responsibility for losses caused
by natural disasters (such as earthquakes, floods, etc.) that exceed
our scope of responsibility.
In any case, our company does not assume any responsibility for
losses caused by using this product, such as loss of profits, loss of
reputa�on, business interrup�on, loss or change of stored data,
and any special, unexpected, associated or intermi�ent losses ca-
used by the above.
Our company does not assume the responsibility for the losses ca-
used by due to improper use of hardware or so�ware not specified
by the our company .
Our company does not provide any form of warranty or technical
support for the informa�on, data, files, other products, services
obtained though the use of this product, and does not assume any
responsibility for the use of above descrip�on by users.
Our company are not take any form of guarantee for third-party
so�ware used by this product.
Due to the con�nuous improvement of the products, the opera�on
and common problems of the models described in the manual are
mainly based on actual machines. And it may be changed without
no�ce.
▲
▲
▲
▲
▲
▲
This device complies with part 15 of the FCC Rules.
Opera�on is subject to the following two condi�ons:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including int-
erference that may cause undesired opera�on.
FCC Warning
FCC ID
：
2AUTE-3378
Any Changes or modifica�ons not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment. This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protec�on
against harmful interference in a residen�al installa�on. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruc�ons, may cause harmful
interference to radio communica�ons. However, there is no guarantee that
interference will not occur in a par�cular installa�on. If this equipment does
cause harmful interference to radio or television recep�on, which can be
determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separa�on between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
