xFusion Digital Technologies FusionServer 2288 V5 Manual Download Page 34

Page: 34 / 86

FusionServer 2288 V5 Server
Technical White Paper

5 Hardware Description

2022-11-11

M.2 FRU Indicators

Figure 5-22

M.2 FRU indicators

Table 5-9

M.2 FRU indicator description

Indicator

Description

M.2 FRU fault indicator

⚫

Off: The M.2 FRU is running properly.

⚫

Blinking yellow: The M.2 FRU is being located, or RAID
is being rebuilt.

⚫

Steady yellow: The M.2 FRU is faulty or not detected.

M.2 FRU activity
indicator

⚫

Off: The M.2 FRU is not in position or is faulty.

⚫

Blinking green: Data is being read, written, or
synchronized.

⚫

Steady green: The M.2 FRU is inactive.

5.5.4 RAID Controller Card

The RAID controller card supports RAID configuration, RAID level migration, and drive
roaming.

⚫

Contact your local sales representative or use the

Compatibility Checker

to determine the

components to be used.

⚫

For details about the RAID controller card, see

V5 Server RAID Controller Card User

Guide

5.6 Network

5.6.1 LOMs

LOMs provide network expansion capabilities.

Summary of Contents for FusionServer 2288 V5























































































Search results

Summary of Contents for FusionServer 2288 V5

Reviews:

Related manuals for FusionServer 2288 V5

Brands by name

Popular brands

xFusion Digital Technologies FusionServer 2288 V5, Manual

Search results

Summary of Contents for FusionServer 2288 V5

Reviews:

Related manuals for FusionServer 2288 V5

Brands by name

Popular brands