Xerox WorkCentre 5790 Series, Service Manual

Page: 1437 / 1610

May 2013
6-53 Xerox® WorkCentre® 5790 Family
GP 22
General Procedures/Information
GP 22 Electrical Power Requirements
Power Requirements
Refer to Table 1 and Table 3 .
Power Save Modes
There are two power save modes which are entered after pre-set timers have expired, low
power mode and sleep mode. Both of these power modes are initially set to factory default time
values but are customer adjustable. Entry to both modes can set by the customer to be either
‘job activated’ or ‘intelligent ready’. The machine will automatically enter low power, then sleep
mode after a period of inactivity exceeds a timer value, refer to
Table 2 . If ‘intelligent ready’ is
set, the default value for the timer is preset but is adjusted by the machine based on customer
usage.
Low Power Mode
Low power mode is automatically entered after a period of inactivity (determined by timer set-
ting) whilst in standby/ready mode. Timer setting range is from 1 to 120 minutes, refer to
Table
2 for the default settings. Single board controller disk off, IOT +24V disabled, ROS motor off,
fuser to low power. The mode of power is returned to standby following a user request, a key
pressed on the user interface, offline staple button, power switch, document in the DADH,
DADH opened, incoming FAX or print job. Entry into low power mode is controlled by
Sleep Mode
Sleep mode is automatically entered after a period of inactivity (determined by timer setting)
whilst in Low Power Mode. Timer setting range is from 10 to 120 minutes, refer to
Table 2 for
the default settings. The mode of power is returned to standby following a user request, a key
press on the user interface, power switch, incoming FAX or print job.
Power consumption
Refer to Table 3 for power the consumption of all modes:
Table 1 Electrical power requirements
Nominal Voltage
Average current
Comments 35-55 ppm 65-90 ppm
110VAC (60Hz)
Plus 6% minus 10% Less than or equal
to 13.2A RMS. Less than or equal
to 17.6A RMS. Specific XLA markets only.
127VAC (60Hz)
Plus 6% minus 10% Less than or equal
to 13.2A RMS. Less than or equal
to 17.6A RMS. Mandatory for Saudi Arabia
only.
127VAC (60Hz)
Plus 6% minus 10% Less than or equal
to 13.2A RMS. Less than or equal
to 17.6A RMS. To operate at 10%
for long periods. Mandatory
for Mexico only.
120VAC (60Hz)
Plus 6% minus 10% Less than or equal
to 13.2A RMS. Less than or equal
to 17.6A RMS. Run mode, USA and Can-
ada.
120VAC (60Hz)
Plus 6% minus 10% Less than or equal
to 13.2A RMS. Less than or equal
to 17.6A RMS. Warm up, All 60Hz markets
including USA and Canada.
220VAC (50Hz)
Plus 6% minus 10% Less than or equal
to 10A RMS. Less than or equal
to 10A RMS. Europe and other 50Hz
markets.
230VAC (50Hz)
Plus 6% minus 10% Less than or equal
to 10A RMS Less than or equal
to 10A RMS. Europe and other 50Hz
markets.
240VAC (50Hz)
Plus 6% minus 10% Less than or equal
to 10A RMS. Less than or equal
to 10A RMS. Europe and other 50Hz
markets.
Table 2 Default settings
Speed
Standby to low
power mode (mins.)
Low power mode to
sleep mode (mins.)
35 ppm 1 5
40 ppm 2 45
45 ppm 5 45
55 ppm 8 45
65 ppm 8 45
75 ppm 15 45
90 ppm 15 45
Table 3 Power consumption in all modes
Configuration
Run mode
(Watt)
Standby
(Watt) Low power (Watt) Sleep (Watt) Plug-in/off mode (Watt)
EPA Typical Energy
Consumption Value (Kwh/week)
35 ppm 1050 290 Less than 125 Less than 15 Less than or equal to 0.9 7.0
40 ppm 1050 290 Less than 125 Less than 15 Less than or equal to 0.9 9.6
45 ppm 1150 290 Less than 125 Less than 15 Less than or equal to 0.9 10.7
55 ppm 1250 290 Less than 125 Less than 15 Less than or equal to 0.9 12.5
65 ppm 1550 310 Less than 160 Less than 15 Less than or equal to 0.9 13.7
75 ppm 1600 310 Less than 160 Less than 15 Less than or equal to 0.9 15.8
90 ppm 1650 310 Less than 160 Less than 15 Less than or equal to 0.9 16.8
Additional power for 1K LCSS 70 10 0 0 0 N/A