Xerox WorkCentre 5022, Service Manual

Page: 528 / 698

06/2014
6-100 WC 5022/5024
6.3.21 NVM FAX
Version 1.0 General
690-435 FAXBOX_CTC_NUMBER 0 15 13 O O The number of ECM/CTC sends for Fax Job.
690-436 FAXBOX_T5_TIMER 60 60 60 X X The RNR signal timer (seconds) (fixed value) for Fax Job.
60 = 60 s
690-437 FAXBOX_RTN_PERCENT 0 100 10 O O The Send Reference of RTN Command (%) (proportion) for Fax Job.
690-438 FAXBOX_EXTEND_DIS_DTC 0 0 0 X X The number of DIS/DTC FIF send bytes (fixed value) for Fax Job.
0 = Auto
690-439 FAXBOX_DROP_OUT_TIMER 6 6 6 X X The image information receive dropout monitoring timer value (seconds)
(fixed value) for Fax Job. 6 = 6 seconds.
690-440 FAXBOX_RX_RESOLUTION 0 4 4 O O The resolution specification during receive for Fax Job.
0 = STD, 1 = STD + FINE, 4 = S-FINE
690-441 FAXBOX_DATA_FORMAT 0 3 3 O O The Encoding Method (send/receive) for Fax Job.
0 = T30_MH, 1 = T30_MR, 2 = T30_MMR, 3 = T30_JBIG
690-450 FAXBOX_V34_MODEM_PERMITTED 0 1 1 O O The V34 capability for Fax Job.
0 = OFF, 1 = ON
690-451 FAXBOX_V34_SYMBOL_RATE 1 5 5 O O The max. permissible value of symbol speed for Fax Job.
1 = 2400, 2 = 2800, 3 = 3000, 4 = 3200, 5 = 3429
690-452 FAXBOX_V34_FIRST_TX_SPEED 1 14 14 O O The max. value of bit speed for Fax Job.
1=2400,2=4800,3=7200,-,12=28800,13=31200,14=33600
690-453 FAXBOX_V34_SYMBOL_ENABLE 0 255 240 O O The enable instruction of symbol speed for Fax Job.
(When 0 to 15 is set, this is not in use).
690-454 FAXBOX_V34_CTRL_BIT_RATE 0 0 0 X X The control channel bit speed (fixed value) for Fax Job.
0 = 1200 bps
690-455 FAXBOX_V34_ANSAM_PHASE_REVERSAL 1 1 1 X X The ANSam phase reversal (fixed value) for Fax Job.
1 = Reverse
690-456 FAXBOX_V8_TE_TIME 10 10 10 O O The V8 Te time (100 ms) (fixed value) for Fax Job.
10 = 1000 ms
690-457 FAXBOX_V34_CC_TIMER 35 35 35 X X The timeout time from V34 mode (Phase 2) to control channel (seconds)
(fixed value) for Fax Job.
35 = 35 s
690-458 FAXBOX_V34_SHIFT_G3 0 0 0 X X The G3 mode transition at V34 CC timeout (fixed value) for Fax Job.
0 = Do not transition
690-459 FAXBOX_ANSAM_SEND_TIME 4 4 4 X X The ANSam signal max. send time (seconds) (fixed value) for Fax Job.
4 = 4 s
690-460 FAXBOX_ANSAM_START_TIME 2 2 2 X X The time from line close to ANSam send (seconds) (fixed value) for Fax
Job. 2 = 2 seconds.
690-461 FAXBOX_V34_GAIN_CHANGE 1 1 1 X X The V34 receive gain switching (fixed value) for Fax Job.
1 = Perform
690-462 FAXBOX_V34_FLAME 0 1 0 O O The V34 1 frame size for Fax Job.
0=256, 1=64
690-470 FAXBOX_NT_PAUSE_DURATION 0 255 *1 O O The pause time (100 ms) for Fax Job.
690-471 FAXBOX_PBX_SELECTION_ENABLED 0 255 3 O O The public network selection Send Signals time (seconds) for Fax Job.
Table 1 FAX
Chain-
Link
NVM Name
Setting
Range
(Minimu
m Value) Setting
Range
(Maximu
m Value)
Default
Value
Write
Allowed/
Protected Default
Value
Yes/No
Description